boldenone acetate

[Red_subbottom]

Does anyone have suggestions on how to get boldenone acetate to dissolve?

I’m at
150 ml total oil volume
65 mg/ml
2% BA
18% BB
75% EO 25% MCT

After 2-3 days fine crystals form by what looks like hundreds of little strands. They are not the jagged thick crystals that grow from the bottom.

Any suggestions much appreciated.

 

[theotherguy]

Nope, but I have some I was about to brew up really soon. I’m glad I saw this post.

 

[Red_subbottom]

Nope, but I have some I was about to brew up really soon. I’m glad I saw this post.

I up BB to 22 %. I’ll see if that’s better.

 

[theotherguy]

I up BB to 22 %. I’ll see if that’s better.

With my bold cyp I had to go up to 27-28% BUT, it’s a different compound, so it may not need that much. But at 65 mg/mL, it would seem that you shouldn’t have to take BB that high. Does the EO help with dissolving?

 

[Red_subbottom]

With my bold cyp I had to go up to 27-28% BUT, it’s a different compound, so it may not need that much. But at 65 mg/mL, it would seem that you shouldn’t have to take BB that high. Does the EO help with dissolving?

EO is considered a solvent. But not like BB… People use it for higher dose gear too. It’s really thin oil. But some people have a reaction to it. It’s never bothered me. I’ve always used USP EO. This is what I know it as:

Ethyl oleate is used as a solvent for pharmaceutical drug preparations involving lipophilic substances such as steroids.

 

[MixModz]

With my bold cyp I had to go up to 27-28% BUT, it’s a different compound, so it may not need that much. But at 65 mg/mL, it would seem that you shouldn’t have to take BB that high. Does the EO help with dissolving?

I have made bold c with 6% bb 1% ba only mct at 100mg /ml

And after a month it’s still perfect, very fluid just the pip hit hard

 

[theotherguy]

I have made bold c with 6% bb 1% ba only mct at 100mg /ml

And after a month it’s still perfect, very fluid just the pip hit hard

That's the one compound I just seem to have issues with brewing

 

[MixModz]

That's the one compound I just seem to have issues with brewing

You should heat up the oil only and after 100 degrees, poor the oil over the powder

And lets heat up until the prep is completely colourless is you use mct
But yes without gu is completely impossible to use this compound after brewing it
Even at 100mg/ml it’s painful okay not like bold acetate but thats hurt

 

[theotherguy]

You should heat up the oil only and after 100 degrees, poor the oil over the powder

And lets heat up until the prep is completely colourless is you use mct
But yes without gu is completely impossible to use this compound after brewing it
Even at 100mg/ml it’s painful okay not like bold acetate but thats hurt

Mine has zero PIP even at 200 mg/mL

 

[MixModz]

Mine has zero PIP even at 200 mg/mL

okay what is you’re receipe ?

 

[theotherguy]

okay what is you’re receipe ?

It’s been a bit since I brewed it, but I think it was 2/25 in MCT oil, no super solvents or anything like that

 

[MixModz]

It’s been a bit since I brewed it, but I think it was 2/25 in MCT oil, no super solvents or anything like that

Okay so why with less solvant and less concentration i have Pip and you don’t ?

 

[theotherguy]

Okay so why with less solvant and less concentration i have Pip and you don’t ?

I wish I could tell you, maybe it’s raws quality? Carrier oil quality? I don’t know

 

[MixModz]

I wish I could tell you, maybe it’s raws quality? Carrier oil quality? I don’t know

Raw from qingdao
Mct only in the bottle

 

[theotherguy]

I’ve used qingdao and PPL for raws and didn’t have an issue with either one.

 

[MixModz]

I’ve used qingdao and PPL for raws and didn’t have an issue with either one.

Yep so I don’t know why it’s so painful