How shitty is this Masteron raw?

[Justaguy99]

A

I have sent all of those photos above to mg agent and she said that lab confirmed the raw is good and they had no problem dissolving it. They just won't admit their mistake.

My supplier is from China. Out of respect for our previous cooperation I don't want to call them out publicly until legit testing confirms my claims.

When I do test it I will send the results back to them and if they refuse to compensate for it I will call them out publicly.

As of now there's no mistake.
You trust enough to inject untested.
But it melts different so they are no longer trustworthy?
Who doesn't test raws to begin with.
And probably sharing it to boot.
Label says Test bro.

 

[readalot]

I have sent all of those photos above to mg agent and she said that lab confirmed the raw is good and they had no problem dissolving it. They just won't admit their mistake.

My supplier is from China. Out of respect for our previous cooperation I don't want to call them out publicly until legit testing confirms my claims.

When I do test it I will send the results back to them and if they refuse to compensate for it I will call them out publicly.

I'll be here. Love to see it. Special place for these people if your claims are true.

 

[PermaBlastingTren]

So terrible that you should send it to me so I can dispose of it in my asscheek

 

[Luka.Halotestin]

Started melting around 105°C and melted completely around 120°C.

 

[UncleBuns]

You can receive sizeable quantities of AAS powder but can't send a small amount to Jano and test it for $120 USD?

 

[Dirthand]

When I do test it I will send the results back to them and if they refuse to compensate for it I will call them out publicly.

So if they compensate you you will keep quite about who send you bad raws??

 

[readalot]

Started melting around 105°C and melted completely around 120°C.

So what is your conclusion based on evidence in hand?

Next steps?

 

[ThinkTrenbolone]

I recommend

contact@analizabialek.com



Blind testing is fine. Payment after he tests your sample.

55 dollars plus shipping

Cheaper by far and the fact he doesn't need you identify it before hand gives more trust.

 

[readalot]

the fact he doesn't need you identify it before hand

The competition requires you to identify?

 

[Dirthand]

The competition requires you to identify?

No jano does not...

 

[iris]

I recommend View attachment 298176

contact@analizabialek.com



Blind testing is fine. Payment after he tests your sample.

55 dollars plus shipping

Cheaper by far and the fact he doesn't need you identify it before hand gives more trust.

But they also fucked up big time, in the past.
Hence people prefer using Jano.
Also, Jano can blind test

 

[readalot]

No jano does not...

Exactly. Don't know what he's getting at. Who is this other competitor? Would defeat the whole purpose identifying the presumed ID beforehand.

 

[ThinkTrenbolone]

But they also fucked up big time, in the past.
Hence people prefer using Jano.
Also, Jano can blind test

Makes sense. I'ma try it though

 

[Luka.Halotestin]

So what is your conclusion based on evidence in hand?

Next steps?

I dunno. It is masteron's melting point. I'll probably try sending it to some lab from this forum for testing.

Even if it is Masteron there is something in there that just won't dissolve and cloggs my filters. The solution just won't clear up.

 

[narta]

Started melting around 105°C and melted completely around 120°C.

That's not how you perform a mp test... You need a tube with mineral oil that has submerged a second smaller tube with the sample and the thermometer. Heat the tube to aprox 20c below the target melting point and increase 1c every 30" after that and see where it melts.

 

[readalot]

6.1D: Step-by-Step Procedures for Melting Point Determination

There are a variety of methods by which a sample's melting point can be measured, with the newest being electrical probes (e.g. Vernier MeltStation). Presented in this section are traditional methods …

chem.libretexts.org

 

[Luka.Halotestin]

Just wanted to share my thoughts...

First of all, thank you pointing out how dumb it was for me to not test my suppliers raws. I sure as hell will do something about that.

But this is what bothers me - let's say I buy raws and they test below 90% for instance. What can I do about it? Is there a source here that will genuinely accept their fault and reship or I just know my raw sucks and toss it into trash?

 

[Spaceman Spiff]

Just wanted to share my thoughts...

First of all, thank you pointing out how dumb it was for me to not test my suppliers raws. I sure as hell will do something about that.

But this is what bothers me - let's say I buy raws and they test below 90% for instance. What can I do about it? Is there a source here that will genuinely accept their fault and reship or I just know my raw sucks and toss it into trash?

Depends on the raw material

I would post the results or notify the supplier. Some suppliers have a guarantee of quality.


I have tested a bold c that was 55% from a supplier and they refunded me

 

[Luka.Halotestin]

Depends on the raw material

I would post the results or notify the supplier. Some suppliers have a guarantee of quality.


I have tested a bold c that was 55% from a supplier and they refunded me

Thanks! That's what I wanted to know.

I already made contact with QSC and will buy soon. I've seen that they never failed you. May I ask what is the lowest purity you had from them?

 

[maxtom]

A roidtest but not very accurate. Better to have a lab testing which will help them reship, I believe.