First Homebrewing Experience - A Few Questions

[mike malone]

I have test prop, mast prop, tren ace, sus in 10g of powder and am starting to brew from now.

Yesterday I did a test with 1g of prop.

Here is the protocol I followed:

castor oil - 7ml
powder - 1g
ba - 0.2ml
bb - 2ml

1. I put the ba, bb, and oil into one beaker.

2. I added in 1g of test prop powder into beaker

3. put beaker in a pan with water.

4. heated to 65c for around 15 mins and stirred until all powder was fully dissolved and the solution was clear

5. poured solution into a 0.2 nylon whatman autovial which is connected via 18g needle into a sterile vial.

6. Filtered solution into the sterile vial.

---

The solution looks fine but I am yet to use it.

I have a few questions first.

1) What should the temperature of the water bath/water in pan be? How long should the solution be heated for? Or is this not so important?

2) I washed the beaker with isopropyl and allowed it to evaporate but never took any great precautions to sterilise throughly. How important is this?

Am I correct in thinking the 0.2 filter should clean absolutely everything so I don't need to stress over this?

3) Even with the autovial it's long and tedious to push the solution through. I don't want to have to do this multiple times when I brew a bigger batch.

What is the greatest concentration I can safely make, without pain or risk of infection with test prop, mast prop, tren ace. I've read some people can get 300mg/ml - I would be happy with half of this.

 

[calvare2]

I have test prop, mast prop, tren ace, sus in 10g of powder and am starting to brew from now.

Yesterday I did a test with 1g of prop.

Here is the protocol I followed:

castor oil - 7ml
powder - 1g
ba - 0.2ml
bb - 2ml

1. I put the ba, bb, and oil into one beaker.

2. I added in 1g of test prop powder into beaker

3. put beaker in a pan with water.

4. heated to 65c for around 15 mins and stirred until all powder was fully dissolved and the solution was clear

5. poured solution into a 0.2 nylon whatman autovial which is connected via 18g needle into a sterile vial.

6. Filtered solution into the sterile vial.

---

The solution looks fine but I am yet to use it.

I have a few questions first.

1) What should the temperature of the water bath/water in pan be? How long should the solution be heated for? Or is this not so important?

2) I washed the beaker with isopropyl and allowed it to evaporate but never took any great precautions to sterilise throughly. How important is this?

Am I correct in thinking the 0.2 filter should clean absolutely everything so I don't need to stress over this?

3) Even with the autovial it's long and tedious to push the solution through. I don't want to have to do this multiple times when I brew a bigger batch.

What is the greatest concentration I can safely make, without pain or risk of infection with test prop, mast prop, tren ace. I've read some people can get 300mg/ml - I would be happy with half of this.

The temperature should be high enough to melt your raws in the solution, watch out for tren because it degrades at a lower temp., than the other raws. Running the solution through a 0.2 um filter is enough to get rid of the unwanted stuff like viruses and bacteria, since they are too big to pass through. For the last question, get a bottle top filter, it's easy and less hassle then a syringe filter.


Sent from my iPad using Tapatalk

 

[mike malone]

thanks.

In all honesty - I would prefer to have less oil and higher concentration at the end. So any tips or suggestions on how to make a more potent version of that mix would be great.

 

[calvare2]

To make more concentrated versions of the steroid, you could use ethyl othelate, replacing the oil you would use for it. For example, instead of using 30ml of grapeseed oil you would use 30ml of ethyl othelate.

thanks.

In all honesty - I would prefer to have less oil and higher concentration at the end. So any tips or suggestions on how to make a more potent version of that mix would be great.

Sent from my iPad using Tapatalk

 

[mike malone]

I tried the test prop yesterday and i think the castor oil make it very thick.

What is the best oil to use? I'm thinking about GSO, or safflower oil. Would be awesome if it became think enough for a slin pin.

Can i buy the oil from a local whole foods or do i need to do the whole ups grade thing?

Thanks

 

[HuckingFuge]

To make more concentrated versions of the steroid, you could use ethyl othelate, replacing the oil you would use for it. For example, instead of using 30ml of grapeseed oil you would use 30ml of ethyl othelate.





Sent from my iPad using Tapatalk

you would have the same concentration. if they was both 30ml. you would need to add more powder to a regular recipe, but I don't recommend it with those esters. higher concentration means painful shot.

 

[HuckingFuge]

I tried the test prop yesterday and i think the castor oil make it very thick.

What is the best oil to use? I'm thinking about GSO, or safflower oil. Would be awesome if it became think enough for a slin pin.

Can i buy the oil from a local whole foods or do i need to do the whole ups grade thing?

Thanks

I buy my oil from the store. just make sure it is clean and not full of plant particles.