HGH was foaming after reconstituting it. Did I ruin it? Has anyone else have this happen to them?
MESO-Rx
Anabolic Steroids
Foaming
- Thread starter BigJ89
- Start date
Did you squirt it really fast straight on the puck?
The vaccume seal always catches me off guard. As soon as I punctured it, it started coming out. I tried to get it too run down the side..shit happened fast
Perrin Aybara
Master
You should put some air in the vial before adding bac water to get rid of the vacuum. Also when I'm putting the bac water in I'll bend the syringe against the vial once it's in so it'll shoot the water into the sides rather than blasting the puck.
Thank you for the info...this is my first time using GH so it is a learning experience (an expensive one). So if I'm adding 1.2ml BAC water add that much air or add more air? I was trying to bend it to the side but I didn't compensate for the vacuum and it just started coming out
TideGear
Well-known Member
It'll probably pull 3cc worth of air. Just pull the plunger all the way back, insert needle and let it balance out on its own. You won't even have to push.
So is the general consensus I fucked the GH up this time because of the foaming? I really don't want to have to toss the vial
IDK. Ive had other peptides foam a lil from the squirt, but didnt notice any decrease in quality. Even the HGH I had foam up when I first started it and still didnt notice any negatives. Im sure someone with more knowledge will say otherwise, but this is just my experience.
Appreciate the reply brother
Mighty-mouse
Well-known Member
You should be ok mine do that from time to time. Pin and be happy
Mayne
Well-known Member
Be mindful how much air you inject in the vial as if you inject way too much it will shoot the solution back out after you pull the needle out of the vial. What I do is find the little indention mark on the rubber top on the side (there are 2 of them where the rubber insterts into the vial) and enter with the needle at an angle to have it's tip between the 2 rubber parts and then it just draws itself into it by the wall of the vial
So you don't inject any air at all before injecting the BAC water?
jm416
New Member
Fir
first put just the needle without the syringe in the stopper to release the vacuum then add your 1.2 cc of bac water
Mayne
Well-known Member
Before the reconstitution no I only inject air before my initial draw equal to it so the vacuum wouldn't pull the solution back in when I pull the needle out of the vial. Just hold the syringe with your fist while blocking the plunger with your thumb and release bit by bit once you are inside the indention mark on the rubber top if your vial has that. Also if you enter at an angle with the vial tilted and the hole of the needle pointed the opposite way of the puck and the needle tip against a wall while blocking the plunger it will do anyway. What I have noticed with mine is that different batches would foam or not no matter what my technique is I think it would have to do with fillers instead of the rhGH because I am literally able to watch a tiny droplet slide down the wall the way I do it and yet it would foam (Mauve top batch #51) or not (Black top batch #41) from my experience anyway
Thank you for the detailed answer. I get what your saying, as long as it's running down the side and not blasting the puck I should be good? Next vial il be alittle better prepared.......side question what gauge/length slin pin does everyone use? I use 31G 5/16 length....what's standard or does it not really Matter?
JP1979
Well-known Member
Depends how lean you are really. I can’t (don’t like to) use 1/2” in my belly 5/16” is great, love handles 1/2”.... well because that’s where all my fat is.
Love handles....the bane of my existence
Whoremoans
Member
Every time I reconstitute a vial of opti gh it looks a little bit “foamy”. No bubbles, but a kind of foam look. And this is with squirting the bac water down the side of the glass.
Me too bro. I blame my mom for letting me eat icing straight from the can as a kid. Lol
Similar threads
