Nandrolone (Deca) 500mg/ml, is this going to hurt like hell?

[KeenObserver]

Hi all,

As a part of my most recent order, I have received this Deca dosed at 500mg/ml. The website did not have any dosed at 250mg/ml that was available to be shipped to me in Australia so I went with this instead.

I plan on doing 500mg a week. So my question to you is, will a 250mg (0.5ml) shot of this cause significant PIP because of the unusually high concentration?

Additionally, Dragon Pharma is one of the only labs I have seen that even make Deca dosed this high, so is it likely that it is even dosed correctly? I am still a few months off running it so perhaps I will send it off to be tested first.

Any help here is appreciated, thank you.

 

[jJjburton]

Hi all,

As a part of my most recent order, I have received this Deca dosed at 500mg/ml. The website did not have any dosed at 250mg/ml that was available to be shipped to me in Australia so I went with this instead.

I plan on doing 500mg a week. So my question to you is, will a 250mg (0.5ml) shot of this cause significant PIP because of the unusually high concentration?

Additionally, Dragon Pharma is one of the only labs I have seen that even make Deca dosed this high, so is it likely that it is even dosed correctly? I am still a few months off running it so perhaps I will send it off to be tested first.

Any help here is appreciated, thank you.

I ran pcom deca 500 and no pip, you can dilute with your testosterone in one syringe, that will help. Start low and in glutes. Glues always has less pip for me

 

[KeenObserver]

I ran pcom deca 500 and no pip, you can dilute with your testosterone in one syringe, that will help. Start low and in glutes. Glues always has less pip for me

Awesome.

So basically, draw in the Test E (250/ml), switch out to a fresh drawing needle, and draw up half a ml of deca 500 and shoot it? Sounds easy enough

 

[ConfusedAF]

Awesome.

So basically, draw in the Test E (250/ml), switch out to a fresh drawing needle, and draw up half a ml of deca 500 and shoot it? Sounds easy enough

Draw Test and Deca with one drawing needle, then switch to a pinning needle for your injection

 

[KeenObserver]

Draw Test and Deca with one drawing needle, then switch to a pinning needle for your injection

Okay so there's no issues with dipping the same drawing needle in both compounds?

 

[ConfusedAF]

Okay so there's no issues with dipping the same drawing needle in both compounds?

Well, I was a bit worried that the second vial might get contaminated with the first compound, but most people will tell you not to be concerned about that.

My suggestion is to draw Test first before Deca, as I prefer the Deca vial to be contaminated with a bit of Test, not the other way around. This way your Test vial remains 'clean' and is good to go for cruise (as I only use solo Test for cruise).

 

[Rido]

Lol cutting with test e to minimize injection pain. Seems a little interesting. Let us know how it goes OP

 

[ConfusedAF]

Lol cutting with test e to minimize injection pain. Seems a little interesting. Let us know how it goes OP

Let's hope his source didn't give him the infamous PIP-generating-Test-E

 

[1Megaman]

How many cycles have you done? What is your planned cycle? The questions you are asking are very basic man.

 

[KeenObserver]

How many cycles have you done? What is your planned cycle? The questions you are asking are very basic man.

How is this information relevant to Deca 500mg/ml pip?

 

[1Megaman]

How is this information relevant to Deca 500mg/ml pip?

Nothing, his questions are very basic just trying to see what his plans are. Maybe it’s his first cycle? Then why run the Deca?

 

[bdsupplements]

This is a good question KeenObserver. The level of PIP would depend on what solvent was used to make the 500mg/ml Deca. If guiaicol or Ethyl Oleate was used, it may not have PIP. If Dragon Pharma simply used Benzyl Benzoate as the solvent, it may have some serious PIP. Something dosed this high, I would tend to think it would have a super solvent in it like guaiacol. I never tried to make Deca dosed this high, so I don't have any empirical evidence to share with you. However, I did make a 200mg/ml testosterone propionate using only larger than normal amounts of BB, and it was nearly impossible to shoot alone because the PIP was so bad. I had warnings to my customers next to the product about the PIP, and I suggested to everyone that they mix it with a compound that traditionally does not generate PIP such as Test E, Test C, or 200-300mg/ml Deca. Some of the guys on this thread, jJjBurton and ConfusedAF, already mentioned this technique, and it is very sage advice. I have a lot of empirical evidence illuminating this as viable option to reduce PIP.

 

[KeenObserver]

Nothing, his questions are very basic just trying to see what his plans are. Maybe it’s his first cycle? Then why run the Deca?

Hi, no it is not my first cycle. Just never pinned anything above 250mg/ml and wanted to know what I was in for.

 

[1Megaman]

Hi, no it is not my first cycle. Just never pinned anything above 250mg/ml and wanted to know what I was in for.

Right on, I have never had pip from high concentrate Deca. Just mix it with whatever else you are running if you are worried about it and enjoy the cycle.