Problems with Testo E. And Tren A By steroidstour

[MrLoop]

Hello
I brewed testo E by steroidstour it was so milky. I Never had this before . no matter how much I warm it up, it goes clear and then milky again .(Look at Photo

and the Tren Acetat leaves a brown / yellowish color lm filter is that normal? I never had that with tren enanthate

All both Products by Steroidstour.
Is Here any one with Same Problem .
Pls Look in photo

Thanks A lot

 

[TRT@40]

Hello
I brewed testo E by steroidstour it was so milky. I Never had this before . no matter how much I warm it up, it goes clear and then milky again .(Look at Photo

and the Tren Acetat leaves a brown / yellowish color lm filter is that normal? I never had that with tren enanthate

All both Products by Steroidstour.
Is Here any one with Same Problem .
Pls Look in photo

Thanks A lot

Can you describe your brewing process in detail?
was there any water involved in any way in your brewing process?

I have brewed their test cyp, npp, primobolan e (220mg/ml) and all tested to be very pure. But any supplier is only as good as their last tested batches.

 

[MrLoop]

no water bath, i heat it directly on a hot plate. and had to heat it up very strongly until it was clean and as soon as it cools down a bit, it becomes like milk again

 

[TrennedOutLunatic]

Recipe?
How many degrees heat?
Did you let it sit before pouring it in the filter?
Type of filter?

 

[MrLoop]

Only EO and 2% BA
The recipe i used since years.
So now i heat it very hot and Its clear.
After cool down i is so milky like real milk

 

[TrennedOutLunatic]

Temperature used?
Did you let it sit to cool down to room temperature at least,before pouring it into the filter?
Type of filter?

 

[MrLoop]

Temperature used?
Did you let it sit to cool down to room temperature at least,before pouring it into the filter?
Type of filter?

Filter 45um Vacuum filter.
I filtered the solution of the Solution is Hot , cause Its better to filter.
Temperature was 80 C cause the Solution was so milky , mostly i brewed Not more then 50-60 C
i really brewed since 8 years . Never had this Problem with so milky testo e.

Its normal that the Filter is so brown by Tren A ? Cause i only brewed Tren E and never See Color changed in filter

 

[TrennedOutLunatic]

Case closed.
You dissolved the filter.
It's the combination of EO and high heat.
80c direct to the membrane plus eo.
It is the filter's particles.
The 0.45 filters are too big. 0.22 is the standard.

Some have corrected this with refiltering.

I am guilty of the same mistake too. Tossed a whole brew this way.

 

[MrLoop]

I brewed since 8 years . Never had this Problem before and i only use 45um Filter.
I Never had this problem before. Its the First raw thats so milky.

so you See the Solution is clear After heating and now Look After its cool down a Little Bit

 

[TrennedOutLunatic]

Yes. You are dissolving again and again the filter particles and then they go solid again once the solution cools down.

 

[MrLoop]

Yes. You are dissolving again and again the filter particles and then they go solid again once the solution cools down.

but why, before i Filtered the Solution, i had to heat it so much , before it was clear Solution? It was 100C .
After this it was clear.
Never had this milky Problem . All raws was clear After they get the melting point

 

[TrennedOutLunatic]

What raw needs 100c? Then you poured this shit on the filter ,with EO.

Learn from your mistake and move on.
The solution temperature should be normal when you are filtering.
If you want faster filtration, just add A LITTLE HEAT.
You are using wrong pore size. You should be using 0.22 instead of 0.45um.

You got your answer.
Now either change the way you are doing it or don't. No problem.

 

[MrLoop]

What raw needs 100c? Then you poured this shit on the filter ,with EO.

Learn from your mistake and move on.
The solution temperature should be normal when you are filtering.
If you want faster filtration, just add A LITTLE HEAT.
You are using wrong pore size. You should be using 0.22 instead of 0.45um.

You got your answer.
Now either change the way you are doing it or don't. No problem.

I think you don't quite understand what I mean. It only became a clear liquid after I heated it to almost 100 C. before that it was milky even without filters. I had never had this problem with Testo E raw material in my 8 years. all my brewed things were always clear and if it worked like this for more than 8 years, what should go wrong now? it can only be on raw material lie. because if it were as you say it would at least have to be before filter be clear

 

[TrennedOutLunatic]

I think you don't quite understand what I mean. It only became a clear liquid after I heated it to almost 100 C. before that it was milky even without filters. I had never had this problem with Testo E raw material in my 8 years. all my brewed things were always clear and if it worked like this for more than 8 years, what should go wrong now? it can only be on raw material lie. because if it were as you say it would at least have to be before filter be clear

Okay. Got you.
Testing time.
Hplc

 

[MrLoop]

Okay. Got you.
Testing time.
Hplc

for 50g t.e ?
First i wait of answer by ST and i will See what they say .
I also Wondered That the Filter is Brown After filtering Tren A . A second problem
I Never had with tren .
dye?? I really dont know .

i Hope they got Good answer if Not i changed my Supplier

 

[TrennedOutLunatic]

Could be dye or some impurity.
If you did everything right,send it for hplc.
I doubt you did everything right.
You don't even know that you shouldn't be using 0.45 um filters.

50g is a big enough amount to be worthy of knowing whether or not it's okay.

 

[MrLoop]

Okay got a Massage back from Steroidstour .

having a problem with the batch.
But They say i get a replacement
I'm curious

 

[Bulldog413]

Shit I just received some test E a couple weeks ago. How long have you had yours

 

[Bulldog413]

Mines going in a blend. It would fuck everything up if my Test E was bad as well.

 

[Nilatac]

They told you or have you figured out what is with the Tren A?