ST anabolic raws source

Thanks brother. That makes It clear for me to avoid EO going forward. I am going trash my EO stock.
I will just use mct, mig840 and gso for next brews.
Glad to help bro! Lol, maybe consider avoiding Mig also, as that contains propylene glycol, which is the main ingredient of antifreeze, which is in so many products we consume today.
 
Glad to help bro! Lol, maybe consider avoiding Mig also, as that contains propylene glycol, which is the main ingredient of antifreeze, which is in so many products we consume today.
Ok yea im gunna look into it but its sounds kinda like there an added risk to bb posibly but the mct holds easyer for whatever reason maybe its cause it thinner but im going to research the other two thanks guys
 
EO is ethyl oleate. Some brewers use it in place of higher BB, which causes more pip. The EO is used to help hold your compound in solution while using less of the other solvents and prevents crashing. Some people are allergic to it though, so not everyone is a fan. I’ve also heard it’s really not good for the body to be used, though I haven’t really looked into it. Hope that helps.
Can i use a little eo in place of bb or maybe a small amount bb with oe plus the regular oil carrier or would i replace with eo just curious
 
Can i use a little eo in place of bb or maybe a small amount bb with oe plus the regular oil carrier or would i replace with eo just curious
Yeah, if you want to keep the BB low, you can use EO as well, on top of the BB. Stanford originally made his Primo 200 (maybe it was 150) in 100% EO.
 
SP Primo was 150mg/ml.
I had some of TGI primo that was 200mg/ml and it was just MCT oil.
My next primo brew will be with mostly MCT oil.
Yeah, People said TGI’s Primo was super smooth even at 200. Never had it but I would think it would have some bite to it.
 
Yeah, People said TGI’s Primo was super smooth even at 200. Never had it but I would think it would have some bite to it.
Yes, it was really smooth; no pip at all. 100% sure there was no GUAC in it either as you can smell the GUAC from miles from the tiniest drop of it.
But because MCT virgin when i used his primo in MCT, i had a small knot at the site of injection. Knot was developed immediately after the pin, was not painful at all and it lasted several weeks.
It was just weird to feel a hard mass at the site of injection. Never had anything like that happen to me before. Perhaps it was just a bad injection.
 
Yes, it was really smooth; no pip at all. 100% sure there was no GUAC in it either as you can smell the GUAC from miles from the tiniest drop of it.
But because MCT virgin when i used his primo in MCT, i had a small knot at the site of injection. Knot was developed immediately after the pin, was not painful at all and it lasted several weeks.
It was just weird to feel a hard mass at the site of injection. Never had anything like that happen to me before. Perhaps it was just a bad injection.
If it never happened again, I’d be willing to bet it was a reaction to the MCT. I think I saw someone shared the recipe and it was just Primo, BA, BB and MCT.
 
Yeah, if you want to keep the BB low, you can use EO as well, on top of the BB. Stanford originally made his Primo 200 (maybe it was 150) in 100% EO.
Ok i was thinking of trying to keep the bb very low and use a little eo ill add a little of each and adjust little by little my goal would be to use a little as posible to get it to suspend as i like to mix 2 or 3 compounds but ill get back to u guys tho im gunna prolly use mct or grapeseed oil then start with with 10 bb ad eo little by little untill i can get it into solution thanks for the info guy
 
Is it unrealistic to expect primo to hold at 200mg/ml in GSO with only BA & BB? I’ve never pinned MCT and am relatively new to homebrew but looking around I’m not convinced that it’s feasible.

I would prefer to avoid any solvent other than BB so is my best bet brewing a small batch of test prop or similar in MCT to see how I tolerate the carrier?
 
Is it unrealistic to expect primo to hold at 200mg/ml in GSO with only BA & BB? I’ve never pinned MCT and am relatively new to homebrew but looking around I’m not convinced that it’s feasible.

I would prefer to avoid any solvent other than BB so is my best bet brewing a small batch of test prop or similar in MCT to see how I tolerate the carrier?

When I get my oil I filter a little and pin a mL to see if there any reaction or pip. That way I don’t have to worry about messing up a batch.
 
Is it unrealistic to expect primo to hold at 200mg/ml in GSO with only BA & BB? I’ve never pinned MCT and am relatively new to homebrew but looking around I’m not convinced that it’s feasible.

I would prefer to avoid any solvent other than BB so is my best bet brewing a small batch of test prop or similar in MCT to see how I tolerate the carrier?
or you could just pin filtered mct by itself to test how your body responds. Try like a ml first time
 
I recently received a pack from ST. Communication was prompt and courteous and TA was very fast. I’m unable to offer any feedback on product quality at this time.
 
Is it unrealistic to expect primo to hold at 200mg/ml in GSO with only BA & BB? I’ve never pinned MCT and am relatively new to homebrew but looking around I’m not convinced that it’s feasible.

I would prefer to avoid any solvent other than BB so is my best bet brewing a small batch of test prop or similar in MCT to see how I tolerate the carrier?

It holds at 250 mg/ml for me with mig840 and 2/20 ba/bb with no PIP. There's a guy that does his at 300 mg/ml with that and gets no PIP. Mig840 is at medlabgear.
 
Fall cycle all brewed with ST raws. Unlabeled bottles are Test E 300. My girl got the wrong ink so I have to wait till we go back to Walmart. Only made 2 bottles tbol to see how I tolerate it. Brewed highest concentrations on oils to limit volume in barrel.

Cycle is 12 weeks
Test E 500
Deca 450
Mast E 400

Might increase dosages midway or so. IMG_1800.jpg
 
Back
Top