Test E/Albuterol For Leaning Out and Keeping Muscle

[Alton Benjamin]

I will be running Pharmacom Test E 300 at 300mg (1cc)per week and will be adding albuterol at 10mg days 1-3, 15mg days 4-6 and between 20-24mg per day on days 7-14. I will use pharmacom arimidex at .25mg every other day beginning on week 2 (this may change to .5mg every three days). For PCT I will use pharmacom clomid for four weeks starting two weeks after last pin. Clomid will be run at 100/50/50/50. I may throw in some Nolva depending on how I feel but since the test e dose is so low, I feel confident a clomid only PCT will do the trick. Goals for this cycle and programming are to retain as much muscle and strength as possible while on a caloric deficit. Current stats are 6'4" tall and 250lbs at around 17% body fat. I would like to get to 230lbs at 10% or lower body fat. I will start at 3500 calories and wean down each week. Macros for the calories will be 40% protein, 30% fat, 30% carbs. Calories weaned will come from carbs.

 

[Alton Benjamin]

Did first pin and albuterol dose today. Pinned 300mg test e and 10mg albuterol divided into two doses. Pinned right glute. No PIP. Let syringe sit in cup of hot water before pin. Little bit of headache after albuterol but went away. I feel totally fine. No test flu, etc. worked chest today. I feel quite week from the lower carb calorie deficit (I've been on the diet for a couple weeks prior to first pin). I am looking forward to the energy from the test in the next few weeks.

 

[Bone Gristle]

Let syringe sit in cup of hot water before pin.

That sounds like a horrible idea.

Sterility is our friend.

 

[Alton Benjamin]

No I mean without the needle attached. Just warmed the oil in the plastic syringe just by letting it stand in hot water for a few minutes. Most people do this or something similar. In no way possible could this induce more bacterial growth capable of entering the bloodstream.

 

[KillaBig]

No I mean without the needle attached. Just warmed the oil in the plastic syringe just by letting it stand in hot water for a few minutes. Most people do this or something similar. In no way possible could this induce more bacterial growth capable of entering the bloodstream.

So a syringe full of oil with no tip on (open end) in water?
A heating pad may be a better option.

Every time I've look'd at the domestic site there Clomid,Nolva,Dex was unavailable.Did you order internationally?

 

[Alton Benjamin]

However..I would enjoy a presentation of your hypothesis on how this practice contributes to increased risk of bacterial exposure.

 

[Bone Gristle]

However..I would enjoy a presentation of your hypothesis on how this practice contributes to increased risk of bacterial exposure.

Is your local water supply bacteria free? Of course not.

Hell, I could probably not wipe the vial or injection area and still have no problems.

Would I want to take that risk for no reason? Fuck no. Everything is find and dandy until they're cutting a abscess from deep within your ass cheek.

 

[Alton Benjamin]

I'm missing where the bacteria gets onto the needle though. I did not put the vial in water, just the syringe/plunger before attaching the needle. So the oil never touches the water and the needle never touches the water. It's actually likely more sterile in the water than in room air. I think you may have just misunderstood what I was doing

 

[Alton Benjamin]

A lot of people will use a syringe heating pad. Same concept.

 

[Alton Benjamin]

The blunt draw needle and cap were still attached and even still I only filled the cup of water about 3/4 full of the length of the syringe so no water touched anywhere near the opening.Since you guys are concerned and trying to help, I suppose it would be best to use a heating pad from now on though. Also @KillaBig..I got mine domestic and had no problems with delays or anything. Are you talking about Frank's site or Darius? I don't think Darius carries Nolva.

 

[Bone Gristle]

The blunt draw needle and cap were still attached and even still I only filled the cup of water about 3/4 full of the length of the syringe so no water touched anywhere near the opening.Since you guys are concerned and trying to help, I suppose it would be best to use a heating pad from now on though. Also @KillaBig..I got mine domestic and had no problems with delays or anything. Are you talking about Frank's site or Darius? I don't think Darius carries Nolva.

Submerging a syringe in water doesn't sound like a good idea to me is all. Just looking out for ya brother. Better safe than sorry.

 

[Alton Benjamin]

Thanks- I think I'm just going to forget heating it and just pin the thing like a man haha.

 

[IronJulius]

Thanks- I think I'm just going to forget heating it and just pin the thing like a man haha.

yea test E is smooth brother no need to heat it

 

[Robfromga]

Warm the vial not the needle. Just dont cover the top in water and wipe with alcohol before drawing. Setting the syringe in water,needle or not, is asking for problems

 

[Dema]

Don't even heat it.. Problem solved... Not like your using high mg gear

 

[Alton Benjamin]

Day 3-
Injection site from Monday did not get sore. I'm very pleasantly surprised with that. Otherwise, bumping albuterol up to 15mg for the next three days..feeling fantastic so far.
Did a back workout on Tuesday. Deadlifts felt very strong. Wednesday was an arms only day. Got a good pump and got out. Today will be legs. Will update again when I ramp the albuterol up to 20mg and pin again on Monday.

 

[Flaming Dragon]

Bro you're in day 3 on Test E.. It's going to be a while before you start to really "feel it". I would say between week 4-6.. That when the fun starts!

 

[Maktub]

Whats your albuterol brand?
I was planning getting some clean but Looks like albuterol is a better option for me .will follow your log.
Thanks

 

[Alton Benjamin]

Whats your albuterol brand?
I was planning getting some clean but Looks like albuterol is a better option for me .will follow your log.
Thanks

Albuterol brand is nephron pharmaceutical corporation

 

[Maktub]

How is the albuterol Hitting you ? Solid?