Tren A/Test P/Masteron with MCT -- What EO %?

Anavarnarian

New Member
Looking for advice on the % of EO that should be used for brewing this particular blend. Oil will be MCT:

50mg Tren Ace
50mg Masteron
50mg Test Prop

Just looking for BA/BB/EO % recommendations for this formulation. I've seen extremely high EO ratios in the recipes floating around out there.

Also, just curious but I have seen instances of injectable Oxandrolone before as well. Would it be possible to add say 50mg of Oxandrolone to the stack as well?

Just noticed this recipe:
(Test p 75mg/ml, tren a 50mg/ml, masteron 50mg/ml) 40mls @ 175mg/ml
  • 3g test prop powder
  • 2g tren a powder
  • 2g masteron powder
  • 15ml EO
  • 10.6ml GSO
  • 1.2ml BA (3%)
  • 8ml BB (20%)

    Would it be better to add an additional 25mg of Test, and does this recipe sound reasonable or is the EO higher than necessary? Thanks guys.
 
Last edited:
If you have the raws, brew separately. Once the mix is done there's no adjusting dosage.

You may want to adjust the mast... But in a mix everything has to be increased.

You gonna need something like 80% EO for that blend though.
 
If you have the raws, brew separately. Once the mix is done there's no adjusting dosage.

You may want to adjust the mast... But in a mix everything has to be increased.

You gonna need something like 80% EO for that blend though.
ABSOLUTELY NOT... EO is only used for high concentrations, he's doing 150mgs only...
 
everything needs to add up to 100%... so if you increase powder then you need to reduce solvents... all to compensate for the total mls.
 
highly doubt you'll get the var in there to hold. But part of the fun of brewing is trying new shit out. Just throw in a half gram of var and a gram of other products and give a small test drive.
 
You saying test prop, tren ace, mast plus adding var and no eo? Good luck with that, lol.
I never said anything about no EO.. .. I said if you do the right ratios, it will work. Also, there are other alternatives to EO as well... what I did say was that you'd be insane to use 80% EO... for just the 3 compounds and no var, at that low of a mg.. you won't need EO.
 
Thank you gentlemen kindly for the feedback.

I think we are going to try the var in this mix just for shits and giggles... I think if it takes that it would be fairly damn interesting.

So no to the 80% EO. Would you say 50% EO in this type of mixture should suffice?
 
Come back when you get the var to hold, I bet a pound to a pinch of shit that the brew will not hold at 50% EO.

Just because someone says it's a no no doesn't mean it's correct.

I have personally done injectable var (without the other compounds) and it's not easy
 
Thanks for this. I might stick to that original EO heavy formulation I found just to be on the safe side and make the proper adjustments to accommodate the var. I'll let you guys know what the outcome of this little experiment is.

I have personally done injectable var (without the other compounds) and it's not easy

Did you get any good personal results and/or feedback on the injectable var? Any PIP?
 
Nothing noticeable over the oral form. And it was through making injectable var I found out I have issues with EO.

It might be best to make a very small amount and see if EO agrees with you or not. You won't get var to hold without it. And you don't wanna waste the raw to find it's unusable for you
 
Come back when you get the var to hold, I bet a pound to a pinch of shit that the brew will not hold at 50% EO.

Just because someone says it's a no no doesn't mean it's correct.

I have personally done injectable var (without the other compounds) and it's not easy
It is not that hard. It will hold well under 50%...or use different solvent.
 
Post up recipe, geargodess. I'll give it a go. I've got powder to burn.
Why would I give away trade secrets... especially if you say your methods work... but if you know what you're doing then just think about it... you'll find the solution.

I can get this without a drop of EO as well... I gave you hints in my previous posts.

Just about anything is possible if the ratios and temps are correct. Just sayin
 
Im going to agree with goddess on this one. You don't need a drop of EO. EO is best used if making sust 350 or t400.

If this is just for personal use and you want it smooth and will easily hold all the raws then yeah, use EO. If you're going to make to resell then just have to find the right % of mix and use mct or cotton seed oil
 
Back
Top