Test cyp crashed

[Mitchy99]

Made this last night at 250mg/ml came home few hours later it was basically completely crystallized
Here's what I did 10grams test cyp powder 2ml ba
And 30.5ml grapeseed oil.

 

[AnTabolic73]

No bb?

 

[AnTabolic73]

A better recipe would've been
10g raws
.8ml ba
8ml bb
About 22ml gso (slightly more to get you to 40ml total product)

 

[AnTabolic73]

If it was me, and I had more raws on hand, I would add 10grams raws and 20ml bb no ba (since you already have 2ml) and then add enough gso to bring the total to 100ml (about 29ml since you already have 30 in there, but enough to top it off at 100ml)

That would yield 100ml at 200mg/ml at 2/20% ba/bb

At 200mg it would have a better chsmce at holding. 250mg would probably hold too, but better safe than sorry.

 

[Mitchy99]

No bb. I'll try your recipe next time. I'm guessing I'm gonna have to heat it to and add some bb to it?

 

[Mitchy99]

I do have 10 more grams sitting at home

 

[AnTabolic73]

No bb. I'll try your recipe next time. I'm guessing I'm gonna have to heat it to and add some bb to it?

Well that's too much ba for only about 40 ml of finished product. That's why I suggested uping it to 100 ml and not adding any more ba and just the bb.

Heat will help get into solution, but you don't want the heat to do most of the work. You want the solvents to take the brunt of the load, otherwise you run the risk of it crashing once the heat is removed. But at that recipe and at 200mg/ml id bet on it holding.

But this is all theoretical, I've never dealt with test cyp.

Maybe @ickyrica Or @LordSamuilo can chime in.

 

[TideGear]

Never made cyp before but will it hold at 250 mg/ml with 1/20?

 

[Evom1]

Definitely need bb. I generally do 1% ba 20% bb

 

[AnTabolic73]

Never made cyp before but will it hold at 250 mg/ml with 1/20?

It's on my to do list as well. But if I had to guess it would hold at 250mg at 2/20. But to be safe id probably just make 200mg 2/20.

 

[TideGear]

Definitely need bb. I generally do 1% ba 20% bb

Ever have any trouble with it crashing? At what concentration are you making it?

 

[Mitchy99]

Ya almost all recipe I found none used bb but I can now see I need to use it. should I filter all this threw again or can I add drops off bb threw the vials after heat is added?

 

[Evom1]

Ever have any trouble with it crashing? At what concentration are you making it?

1/15 it crashed, 1/20 I've always been good. I do 250mg/mg

 

[Evom1]

Ya almost all recipe I found none used bb but I can now see I need to use it

Could you by chance have been looking at test e recipes instead of test c? I've never seen a c recipe call for no bb

 

[AnTabolic73]

Ya almost all recipe I found none used bb but I can now see I need to use it. should I filter all this threw again or can I add drops off bb threw the vials after heat is added?

Nah. You can't salvage that batch with just bb, it probably would have too much pip due to nearly 5%ba content. Best bet would be to scrap it, or salvage it the way I mentioned above. Assuming you have the raws, the bb, and more vials and filters on hand.

 

[AnTabolic73]

Even if you add the 10 ml of bb, it would bring your product to 50ml of 200mg/ml at about 4/20% ba/bb. Still a lot of ba. Itd probably hold, but have a lot of pip. Unless you add oil, but if you add oil you're taking the concentration way below 200mg/ml, unless you add more raws.

 

[AnTabolic73]

Best bet heat it till it gets into solution, and then dump into beaker/graduated cylinder and start over.

 

[Mitchy99]

Well I guess I'll order more vials and start over

 

[Mitchy99]

I dont feel like filtering all that threw a .22 filter again haha takes forever and hurts my hands after a while from the pushing force

 

[Evom1]

I dont feel like filtering all that threw a .22 filter again haha takes forever and hurts my hands after a while from the pushing force

You're using a caulking gun with a 60cc syringe right?