Best instruction setup for newbies and recipes?

[iintensity]

Try this. I use a 250ml beaker. Say you are brewing test e at 200mg/ml.

Ad 20 grams of raw. Then add 5 ml of bb and 1.5ml ba. If it completely dissolved your raw u are gtg. If it doesn't completely disolve, the add 1ml off bb until dissolved at room temp.

When dissolved, you are ready to add oil and filter.

Every ester is different. Cyp takes 20%. Test e is closer to 5%. And god only knows what confious is cutting it with.

As long as it is dissolved, you can add

Test E will actually hold find without any solevents because it's completely soluble in oil. It is rather thick though.

 

[doctor jones]

Try this. I use a 250ml beaker. Say you are brewing test e at 200mg/ml.

Ad 20 grams of raw. Then add 5 ml of bb and 1.5ml ba. If it completely dissolved your raw u are gtg. If it doesn't completely disolve, the add 1ml off bb until dissolved at room temp.

When dissolved, you are ready to add oil and filter.

Every ester is different. Cyp takes 20%. Test e is closer to 5%. And god only knows what confious is cutting it with.

As long as it is dissolved, you can add

So u dont heat or boil ur brew? Most recipes I read requires brewing

 

[Big_paul]

So u dont heat or boil ur brew? Most recipes I read requires brewing

No. I use to, but 22.5nm filter gives you a sterile product so long as your vial and stopper are clear. I do heat vials and stoppers in the oven at 300 degrees if I am not using pre sealed sterile vials. For personal use, use the pre sealed vials.

 

[Big_paul]

So u dont heat or boil ur brew? Most recipes I read requires brewing

Most recipes are posted by guys who brewed 20 years ago when heat was used, or by members who read there posts and take them for gospel. At the time a 45nm filter was suggested, which is not going to filter every thing out of the solution you don't want in your body.

 

[doctor jones]

Right I feel u I read alot recipes alot of the recipes don't use BB and some do, for test cyp and test e, I feel comfortable more with caps, that's da way always done that why, never with solutions ,but bet that up, I'm a newbie to this and I wanna get shit right, it's body that's taken it, I don't wanna fuck, I don't want hard pip

 

[doctor jones]

In other forums or discussions board won't allow any input on raw source or recipes , this a good site

 

[Joejack]

So instead of using the extra oil to push through a filter could you just back fill and the air would push it all through?

 

[XKawN]

Well, there's really no downside to heating 200 - 250f when brewing. I'll heat to about 250f allow the oil to mix itsself and cool down to a very warm state to allow filtering to flow much easier. Big difference in between filtering cold and filtering warm. heating makes the process much easier and quicker and heating at such a low temp there will be no degradation.

 

[Superjet68]

This is my first time brewing as well, Big Paul gave a lot of great advice. How much gso should you add for you 200mg/ml. recipe? And if most raws are underdosed 20%, should you compensate with more powder to get closer to 200mg/ml?

 

[Mechanics]

Good thread .
I have been thinking of getting this a try.
Now that I can get reliable powder.
Will be watching.
@Big_paul u seem that u have alot of personal experience.
I might have some questions for you in the near future if your cool with me asking

 

[XKawN]

This is my first time brewing as well, Big Paul gave a lot of great advice. How much gso should you add for you 200mg/ml. recipe? And if most raws are underdosed 20%, should you compensate with more powder to get closer to 200mg/ml?

most folks overdose their gear. Probably about 10%. I do.

This is my first time brewing as well, Big Paul gave a lot of great advice. How much gso should you add for you 200mg/ml. recipe? And if most raws are underdosed 20%, should you compensate with more powder to get closer to 200mg/ml?

what are you trying to brew at 200mg/ml?

 

[Superjet68]

I am going to attempt to brew test e 250. I was hoping for a proven recipe with exact amounts of powder,bb,ba and gso.

 

[XKawN]

I am going to attempt to brew test e 250. I was hoping for a proven recipe with exact amounts of powder,bb,ba and gso.

31.2 ml oil, .8 ml ba, 10 grams of powder. That will give you 40ml at 250mg/ml at 2%ba. Bb is not necessary for test e. I use 1% ba, but most probably use 2%. More than 2% is rediculous imo. I don't use bb in test e or eq.

 

[Superjet68]

is this formula overdosed to compensate for powder that might be 20% lower?

 

[XKawN]

is this formul79a overdosed to compensate for powder that might be 20% lower?

no. Test e is about .85 in weight (I believe). Double check that. So if you want to add a gram you'll have to subtract .85ml.... make sense? I'm not sure what amount your brewing and believe it or not, when I went to get you recipe from my list of all my notes and recipes I accidentally deleted them all. Oh well, lol.

 

[Superjet68]

Shit bother, I didn't mean for you to delete your stuff, Sorry. I understand what your saying about adding a gram and subtracting. Makes sense. Your 40ml batch would be perfect to make. Thanks

 

[Superjet68]

One more question, do you heat your mix before you filter? I have read a lot of people do not they just run the ba alittle higher

 

[XKawN]

Not a big deal. Most of it I just do from memory. Been doing this for quite a while. Muscle memory, lol.

 

[XKawN]

One more question, do you heat your mix before you filter? I have read a lot of people do not they just run the ba alittle higher

I don't heat to sterilize. I heat to about 250f for about 20 minutes. I use a burner and place the beaker directly on the burner. Just don't add powder first and you won't burn it. I add the oil first and then the powder. The oil when it heats you'll see it moving around which helps mix. At 250f there will be no degradation so there is no down side. I turn the burner off and let cool to a very warm state to filter easily. Too warm and you'll melt your syringe and plastic needle tips. Also, I use 1% ba.

 

[durtBag]

X

Sent from my SM-G930V using Tapatalk