iintensity
New Member
Test E will actually hold find without any solevents because it's completely soluble in oil. It is rather thick though.
MESO-Rx
Anabolic Steroids
Best instruction setup for newbies and recipes?
- Thread starter theNoid
- Start date
doctor jones
New Member
So u dont heat or boil ur brew? Most recipes I read requires brewing
No. I use to, but 22.5nm filter gives you a sterile product so long as your vial and stopper are clear. I do heat vials and stoppers in the oven at 300 degrees if I am not using pre sealed sterile vials. For personal use, use the pre sealed vials.
Most recipes are posted by guys who brewed 20 years ago when heat was used, or by members who read there posts and take them for gospel. At the time a 45nm filter was suggested, which is not going to filter every thing out of the solution you don't want in your body.
doctor jones
New Member
Right I feel u I read alot recipes alot of the recipes don't use BB and some do, for test cyp and test e, I feel comfortable more with caps, that's da way always done that why, never with solutions ,but bet that up, I'm a newbie to this and I wanna get shit right, it's body that's taken it, I don't wanna fuck, I don't want hard pip
doctor jones
New Member
In other forums or discussions board won't allow any input on raw source or recipes , this a good site
Well, there's really no downside to heating 200 - 250f when brewing. I'll heat to about 250f allow the oil to mix itsself and cool down to a very warm state to allow filtering to flow much easier. Big difference in between filtering cold and filtering warm. heating makes the process much easier and quicker and heating at such a low temp there will be no degradation.
Superjet68
New Member
This is my first time brewing as well, Big Paul gave a lot of great advice. How much gso should you add for you 200mg/ml. recipe? And if most raws are underdosed 20%, should you compensate with more powder to get closer to 200mg/ml?
most folks overdose their gear. Probably about 10%. I do.
what are you trying to brew at 200mg/ml?
Superjet68
New Member
I am going to attempt to brew test e 250. I was hoping for a proven recipe with exact amounts of powder,bb,ba and gso.
31.2 ml oil, .8 ml ba, 10 grams of powder. That will give you 40ml at 250mg/ml at 2%ba. Bb is not necessary for test e. I use 1% ba, but most probably use 2%. More than 2% is rediculous imo. I don't use bb in test e or eq.
Superjet68
New Member
is this formula overdosed to compensate for powder that might be 20% lower?
no. Test e is about .85 in weight (I believe). Double check that. So if you want to add a gram you'll have to subtract .85ml.... make sense? I'm not sure what amount your brewing and believe it or not, when I went to get you recipe from my list of all my notes and recipes I accidentally deleted them all. Oh well, lol.
Superjet68
New Member
Shit bother, I didn't mean for you to delete your stuff, Sorry. I understand what your saying about adding a gram and subtracting. Makes sense. Your 40ml batch would be perfect to make. Thanks
Superjet68
New Member
One more question, do you heat your mix before you filter? I have read a lot of people do not they just run the ba alittle higher
Not a big deal. Most of it I just do from memory. Been doing this for quite a while. Muscle memory, lol.
I don't heat to sterilize. I heat to about 250f for about 20 minutes. I use a burner and place the beaker directly on the burner. Just don't add powder first and you won't burn it. I add the oil first and then the powder. The oil when it heats you'll see it moving around which helps mix. At 250f there will be no degradation so there is no down side. I turn the burner off and let cool to a very warm state to filter easily. Too warm and you'll melt your syringe and plastic needle tips. Also, I use 1% ba.
durtBag
New Member
X
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk
