homebrew dudes

[disordermental]

Hello dear friends of the forum, I am trying to make my beer, my doubt comes because after a small batch in which I expected to get 10 vials of 250 of tea. To my surprise, I used 30 grams of enanatate beer because the quality of the testo I bought according to the person's post was 96 percent and not to be short, no one has had that problem, and the first time I tried with only 10 ml, I got confused with the quantities and it came out 22g (I used 026. mg instead of 26g) so this time I added 30 to reach 250, the fact is that after sending Jano's friend I got 199.08, and the only The option that occurs to me is that passing it through the water bath would evaporate part of the testosterone in the mixture. Is this possible? The rest of the material and process is all taken from the information that is here and it is not complicated at all, but if it has happened to anyone else or can shed a little light on me, I would appreciate it, from one brewer to another

 

[TyLu17]

Have you recalculated the quantities using the calculator?

 

[TyLu17]

The Home of Steroid & Homebrew - Steroid Homebrew

Steroid homebrew recipes, calculators and steroid resources

steroidhomebrew.com

It‘s really good

 

[disordermental]

The Home of Steroid & Homebrew - Steroid Homebrew

Steroid homebrew recipes, calculators and steroid resources

steroidhomebrew.com

It‘s really good

Yes, it was what I used to do the calculation, it seems like a very good tool, I did everything based on it being 285-290 mg, that's why the final result surprised me, I know it must be my mistake, but review all the steps and the only thing I could make a mistake in is perhaps leaving the solution a bit too much in the fire since it was the second time, that's why I wanted to ask if this mistake has happened to anyone else as well or should I focus on another point Thank you very much for your response, also dear TyLu, have a good day

 

[Denicnut2427]

Yes, it was what I used to do the calculation, it seems like a very good tool, I did everything based on it being 285-290 mg, that's why the final result surprised me, I know it must be my mistake, but review all the steps and the only thing I could make a mistake in is perhaps leaving the solution a bit too much in the fire since it was the second time, that's why I wanted to ask if this mistake has happened to anyone else as well or should I focus on another point Thank you very much for your response, also dear TyLu, have a good day

It’s easier to just buy a hot plate that you can set to whatever your makings melting point…you probably didn’t burn away drug it’s more under dosed raws, math off, didn’t desolve enough( prob not likely) or filtering bc a good amount of drug is left in filters too

 

[disordermental]

Hello friend, thanks for answering, but what surprises me is that the first time I made a mistake I put 0.26 grams instead of 26 and it came out 22 grams, using more than 100% according to my mathematics and doing everything with the same filters. syringe should have obtained around 250-260 according to a rule of three, that's why I'm so surprised, I don't know if I explained myself well. and thanks for the advice, I will buy that hot plate.

 

[Denicnut2427]

Hello friend, thanks for answering, but what surprises me is that the first time I made a mistake I put 0.26 grams instead of 26 and it came out 22 grams, using more than 100% according to my mathematics and doing everything with the same filters. syringe should have obtained around 250-260 according to a rule of three, that's why I'm so surprised, I don't know if I explained myself well. and thanks for the advice, I will buy that hot plate.

So you put a 1/4 of a gram? When you get raws try to order what you’re going to use at first too…like I got 12g of test prop to do a trial run and wanted to make 10 bottles so I actually had 20% overage in this case but I knew I’d be good and over dosed and in case I bee a couple extra ml it won’t matter