MESO-Rx
Anabolic Steroids
How to prevent injection pain
- Thread starter Fraggle
- Start date
My head is still fucked-up after drinking 4 years from that Jar! LMAO If I had re-uped I'd be a fucking weed or wildflower in some damn field! Semper Fidelis! I had only several incidents with injection pain over a four year period because I like to go overboard and 1,000mg/ml per shot sometimes. This year will be my fourth year. I have instructed a younger sibling also and he has never come to me about injection pain. I read "How to Inject" and now those pages are yellowed from age. Well guys get your gear to room temp, use the proper gauge needle, wipe and clean the area, stick, inject, withdraw, wipe, rub a bit, and use a small circular bandage and then go to work! See ya!
Last edited:
BrolickLabs631
New Member
i think winny is a mixture of benzyle alcohol "BA" and baceteriostatic water, i could be wrong but if those are the two compounds then thats why it hurts, you figure there is an avg. of .2ml of ba in each shot of test so my making that % higher then theres your pain.
Lately my injections have been OK, now for some damn reason, my February injected was fucked up. It left me with a lump that fits right in the palm of hand! I got to figure out did I do wrong. I had this lump for the entire month of February. It only aches a bit and there is no redness, I can still walk and run with no problem,. but this sucker appears to have found a home! LOL
I'm going to use my heat pad and RICE to evict this bastard! LOL
I'm going to use my heat pad and RICE to evict this bastard! LOL
lohyewcheong
New Member
What's the best thing to do if one suspects he is experiencing pain due to High Benzyl Alcohol content?
Would it make a difference to inject a smaller amout per dose? Then maybe increase the no of times a shot is taken per week so the total mg per week is still the same?
Or would it help to mix the high BA steroid with another steroid that you know does NOT cause pain having use it in the past before? Does that sort of dilute the BA a bit?
Would it make a difference to inject a smaller amout per dose? Then maybe increase the no of times a shot is taken per week so the total mg per week is still the same?
Or would it help to mix the high BA steroid with another steroid that you know does NOT cause pain having use it in the past before? Does that sort of dilute the BA a bit?
I don't think that would help. It's the concentration of BA in the shot that's the problem, not the absolute amount of BA.
That's one way that will work. The best way to dilute your gear is to draw some sterile oil into the syringe after you've drawn your gear. This is commonly called "cutting" the gear. You can get some sterile oil online from places like this. One time when I had painful gear, I added .5ml of sterile oil for every 1ml of gear I drew. The injection went from incredibly sore to painless.
lohyewcheong
New Member
Thank you very much for your advice!!
Or, you can put a drawing needle in the top of the rubber not touching any of the gear, use a pan with water and some heat, and you can boil off the excess BA to lower the concintration.
If you are going to do the oil route then use EO.
If you are going to do the oil route then use EO.
jasthace
New Member
Thats a novel idea hacskii ,I didn't think of that one
hi,
i want know more about this....so,pls tell me more...
_________
zenie
http://www.registeredsexualpredators.org/Illinois-Sexual-Predators (Illinois Sexual Predators)
nitro tech
i want know more about this....so,pls tell me more...
_________
zenie
http://www.registeredsexualpredators.org/Illinois-Sexual-Predators (Illinois Sexual Predators)
nitro tech
melchizedeck
New Member
This stuff hurts! I have Supertest 450mg/ml and I'm wondering if I should cut it and at what ratio. Also would letting some of the BA evaporate using a pin while baking in oven help?
1st time on here BTW...
1st time on here BTW...
I think you would be better off with a pan filled with a little water on the stove, the BA boils off fairly easy and will make like frosting on the drawing needle as it is boiling off.
Just be careful how far down the needle goes, if it touches the gear it will push it out of that bottle and into the pan.
Generally though cutting gear with EO oil works very well.
Only bummer is drawing the EO oil, it locks up the syrenge when you try to use it.
Its like it attacks the rubber or something.
Just be careful how far down the needle goes, if it touches the gear it will push it out of that bottle and into the pan.
Generally though cutting gear with EO oil works very well.
Only bummer is drawing the EO oil, it locks up the syrenge when you try to use it.
Its like it attacks the rubber or something.
melchizedeck
New Member
Do you think keeping gear in the syringe is safe (more sterile, less contamination) or should I transfer to vial? The Supertest 450 I need to cut comes in sachets not vials and I need to keep it somewhere.
Thanks!
Thanks!
They have multiuse vials at research shops, I cant see why you could not toss some EO in there and put all that through a filter into a sterile multiuse vial.
Only diffrnece will be less pain but also less mg per ml.
EO is the way to go, killer stuff for thining the gear out and cutting the pain.
Only diffrnece will be less pain but also less mg per ml.
EO is the way to go, killer stuff for thining the gear out and cutting the pain.
What are the benefits to using EO over inexpensive USP oil?
Pain
How is pain a benefit?
