NPP+DHB

[HereToTeachAndLearn]

I am currently injecting about 9ml-12ml per week between Test/NPP/DHB. I plan on trying to cut the volume in at least half, so I was planning on brewing NPP100+DHB100 together. Does anyone have any concerns with this combination? I currently put 1ml of each in a syringe and inject together with 1ml of GSO (for DHB pip), and separately inject 1ml of my favorite test that week.

My ideal would be NPP100+DHB100+TestD200 per ml all in one 1ml injection 3x per week.

Will this hold together? If it does hold, I might be having fun with PIP.

Thoughts?

 

[narta]

I am currently injecting about 9ml-12ml per week between Test/NPP/DHB. I plan on trying to cut the volume in at least half, so I was planning on brewing NPP100+DHB100 together. Does anyone have any concerns with this combination? I currently put 1ml of each in a syringe and inject together with 1ml of GSO (for DHB pip), and separately inject 1ml of my favorite test that week.

My ideal would be NPP100+DHB100+TestD200 per ml all in one 1ml injection 3x per week.

Will this hold together? If it does hold, I might be having fun with PIP.

Thoughts?

It may need to up the BB to something like 25% but it will hold if you use MCT probably

 

[HereToTeachAndLearn]

Thanks.

 

[Obscured78]

Since you're mixing the dhb with npp I wouldn't add the extra oil for pip. Deal with it, it aint that bad. I was doing 1ml test mixed with 1.5ml of dhb.

 

[Denicnut2427]

I am currently injecting about 9ml-12ml per week between Test/NPP/DHB. I plan on trying to cut the volume in at least half, so I was planning on brewing NPP100+DHB100 together. Does anyone have any concerns with this combination? I currently put 1ml of each in a syringe and inject together with 1ml of GSO (for DHB pip), and separately inject 1ml of my favorite test that week.

My ideal would be NPP100+DHB100+TestD200 per ml all in one 1ml injection 3x per week.

Will this hold together? If it does hold, I might be having fun with PIP.

Thoughts?

You would need some ethyl oleate to hold that for sure…I do 100mg dhb in mct at 1% ba and 20% bb regularly and it crashes and gets cloudy…i say try 1% ba and 20% bb and the remaining oil you can do 50:50 EO to mct( I’ve done this for inj dianabol which held but used EO/ grapeseed…the other problem is pain and the way the high mg blends absorb from the depot site in the muscle it’s usually not worth it I rotate between both delts, triceps, glutes, rear delts and I do no injections on Wednesdays ..pm if you need me I have good amount of homebrew experience

 

[HereToTeachAndLearn]

I was injecting MWF - 100mg DHB (1ml) + 1ml GSO (for DHB pip) + 100mg NPP (1ml) = 3ml in glute, and 200-333 Test C,D or E (1ml) in quad. Totaled 12ml per week, injecting glutes with a 25ga and quad with 30ga, both IM.

I just brewed 33ml of (50mg/ml DHB + 50mg/ml NPP + 150mg/ml Test D).

My plan is to inject MTWTFS only 1ml, cutting my oil in half and transitioning to only 30ga needles.

I used:

3% BA
25% BB
q.s. Migylol 840

I injected 1ml in my glute with a 27ga needle as a first test. If all goes well, I will use a 30ga tomorrow.

I believe I was fairly conservative across the board and if the pip is reasonable, I will give this a try until I test lowering / eliminating BB.