PPL Cyp Purity Results

[Deleted member 123722]

Long story short, after getting back shitty bloods (still for unknown reasons), I got into it with the PPL rep at SST, and also came on these boards, thinking it was the raw powder. After much back and forth, I put about $280 to get my cyp powder shipped within days and tested by @janoshik

Here are the results.

 

[Forthewin1123]

Long story short, after getting back shitty bloods (still for unknown reasons), I got into it with the PPL rep at SST, and also came on these boards, thinking it was the raw powder. After much back and forth, I put about $280 to get my cyp powder shipped within days and tested by @janoshik

Here are the results.

View attachment 155973

Glad you did this... the raws aren't the best but not too bad. I wouldn't blame this on your test results for sure... .
You went hard on ppl for awhile.. I commend you for getting it tested knowing it could make you out to be wrong .
I still don't agree with ppl not accepting janos testing.. when 90% or more of all aas testing is through jano.. more then any other hplc lab I've seen..
Goodluck finding the issue woth your bloodwork.. maybe a bad vlood test.. it's some what common.

 

[Upbeatrawfish]

Thanks for sending this in bro, I also have some cyp that seemed weird from PPL, made a brew at 300+mg/ml and it had 0 issues with falling into solution and staying, which was weird because I overdosed it by 10%.
Has anyone had cyp hold over 300mg/ml?

 

[Deleted member 123722]

Well overdosed my Primo by 10% and it stayed as well; apparently MCT oil can hold things together more. So if you used that, perhaps? Idk.

 

[RackPuller]

Thanks for sending this in bro, I also have some cyp that seemed weird from PPL, made a brew at 300+mg/ml and it had 0 issues with falling into solution and staying, which was weird because I overdosed it by 10%.
Has anyone had cyp hold over 300mg/ml?

I’ve been using test cyp 300 in mct 1/18 for a long time never has crashed, always painless

 

[Cashton]

Thanks for sending this in bro, I also have some cyp that seemed weird from PPL, made a brew at 300+mg/ml and it had 0 issues with falling into solution and staying, which was weird because I overdosed it by 10%.
Has anyone had cyp hold over 300mg/ml?

According to this an overdosing if only about 5% is sufficient. Did you use the markings on the glassware to measure volume? Or syringes?

 

[Upbeatrawfish]

According to this an overdosing if only about 5% is sufficient. Did you use the markings on the glassware to measure volume? Or syringes?

Syringes and then weigh each vial. End volume was good. The product works well, I'm just new to brewing cyp and was curious how high people have gotten it to hold?

 

[CApump]

Syringes and then weigh each vial. End volume was good. The product works well, I'm just new to brewing cyp and was curious how high people have gotten it to hold?

In my experience it should not be holding long term at 300. Iv had cyp crash at 250mg/ml with a 5% OD when the house gets into the mid 60’s. That was with 18% bb.

 

[Forthewin1123]

I brew cyp at 250..10% over so more like 275.. 2/20 in mct.. I let it spin for an hour at 120-130°f.. let it cool to 80° add ba .spin for 20-30mins again.. filter and fill/cap.. never had one crash yet.. left a vial in my truck over night recently.. 34° and.it was fine ..I blame 20%bb mct and the long stirring with medium heat.. I believe it makes a stronger bond.. this is not backed by any science..just my opinion from my experience..woth cold brewing and with medium heat

 

[SAZHammer]

Long story short, after getting back shitty bloods (still for unknown reasons), I got into it with the PPL rep at SST, and also came on these boards, thinking it was the raw powder. After much back and forth, I put about $280 to get my cyp powder shipped within days and tested by @janoshik

Here are the results.

View attachment 155973

Can I ask you some questions about the process to send this to Jano?

 

[Deleted member 123722]

Can I ask you some questions about the process to send this to Jano?

Simple. Just email him and he will tell you what to do. I sent it super fast mail because I wanted to know sooner; this wasn't necessary but I had to figure it out sooner than later. Just email him. @janoshik

 

[janoshik]

the email is on my website - janoshik.com

 

[Parabolic]

I brew cyp at 250..10% over so more like 275.. 2/20 in mct.. I let it spin for an hour at 120-130°f.. let it cool to 80° add ba .spin for 20-30mins again.. filter and fill/cap.. never had one crash yet.. left a vial in my truck over night recently.. 34° and.it was fine ..I blame 20%bb mct and the long stirring with medium heat.. I believe it makes a stronger bond.. this is not backed by any science..just my opinion from my experience..woth cold brewing and with medium heat

This is what I plan to brew my next batch at and like you said extra stirring and some heat. I'll probably buy a hotplate stirrer for the job.

We will see how it holds. Many people say they have no issues at 250g/ml though.

 

[theotherguy]

This is what I plan to brew my next batch at and like you said extra stirring and some heat. I'll probably buy a hotplate stirrer for the job.

We will see how it holds. Many people say they have no issues at 250g/ml though.

I’ve brewed all my test cyp at 250 or higher and haven’t had issues

 

[Parabolic]

I’ve brewed all my test cyp at 250 or higher and haven’t had issues

Good to hear.

 

[OmL]

Fair play for the test man, you’re bettering the community.