Villain
Member
You should! Lol. I don’t compliment many people, but you’re likable and knowledgeable.I'm getting a warm fuzzy feeling now.
MESO-Rx
Anabolic Steroids
PurplePandaLabs Raw source
- Thread starter purplepandalabs
- Start date
PandaRep
Member
Villain
Member
DammitI appreciate that!
No, no you're not getting any MORE free gear
Villain
Member
The best he can offer right now is himself. I hope that will suffice. I heard he has a sexy wig collection of various colors to suit your preference though.
Ahhh
the age old question
If you're on Tren and you fuck a dude in a wig... is it gay?
superbane
Well-known Member
you need raws first to be on tren ...
PandaRep
Member
That means I need to shave my legs and ass again... remember how bad those in grown hairs were last time!!!???
Villain
Member
Dude, you may notice I didn’t call you for like a week after that
FR0Z3N_B0MB3RRR
Member
By the way, does anyone recently tried ppl tren raws Ace and enanth to give some feedback about? You cannot escape from nightsweats i think unless you re on keto, and the other known. Because some years ago i brewed a tren hex from a german factory that sold to researchers labs etc (i paid it a LOT) and it was everything crazy about nightmare nightsweats rage hypertrophy etc.. i can try the melting point too.. i ll do it today.. today i brew but as i stated i don t know when i ll pin it, so it would be great to have some feedbacks about
@ickyrica ?
@ickyrica ?
Nice word choice. Bonus points go to you today.
PandaRep
Member
Villain
Member
At least wash your ass out and scrub your balls man!!!!Dude, I fucking showered last week. You can't have it all!!
FR0Z3N_B0MB3RRR
Member
Can someone tell if he did try PPL tren ace and enanth and found if they re legit? thanks
PandaRep
Member
FR0Z3N_B0MB3RRR
Member
Just tried melting point in the hot plate and i cannot have a reliable temperature without the thermometer submerged, i tried like 100mgs of what should be PPL Tren Acetate on the left and something like 100mgs of what should be PPL Tren Enanthate.
Having the info of Tren Ace melting point is 92-95 C and Tren Enanth is 70-75 C, i think PPL tren was legit because the temperature detected wasn t correct in my analysis, but the “Tren E” melted for first... and then after some times did the “Tren A”.. i putted some water when the thermometer was at 60 C and after like a minutes was evaporated.
I tried to warm at 150 C the mix of the 2 powders tested with the mix of them that i brewed one hour ago at 40 C with EO and MCT and it turned dark orange instead of golden yellow that’s the one brewed with virtually no heat. So it seems legit for what i can see now, i ll pin maybe next month.
on the pic, on the Left is 100ml of “tren mix” 7.5g of what should be 2.5g Tren Ace and 5g Tren E. Brewed at 40 C with 20% BB 1% BA 20% EO and 52 % MCT. On the Right is the powder mixed to test melting point plus like 1ml of the mix brewed at 40 C , all the whole warmed at 150 C, and it turned dark orange as i stated.
How do you check melting points? With my hotplate its difficult, i think i ll try with diluiting powder sample with a little bit of water and submerge the thermometer, it can be a reliable way to measure melting point?
Having the info of Tren Ace melting point is 92-95 C and Tren Enanth is 70-75 C, i think PPL tren was legit because the temperature detected wasn t correct in my analysis, but the “Tren E” melted for first... and then after some times did the “Tren A”.. i putted some water when the thermometer was at 60 C and after like a minutes was evaporated.
I tried to warm at 150 C the mix of the 2 powders tested with the mix of them that i brewed one hour ago at 40 C with EO and MCT and it turned dark orange instead of golden yellow that’s the one brewed with virtually no heat. So it seems legit for what i can see now, i ll pin maybe next month.
on the pic, on the Left is 100ml of “tren mix” 7.5g of what should be 2.5g Tren Ace and 5g Tren E. Brewed at 40 C with 20% BB 1% BA 20% EO and 52 % MCT. On the Right is the powder mixed to test melting point plus like 1ml of the mix brewed at 40 C , all the whole warmed at 150 C, and it turned dark orange as i stated.
How do you check melting points? With my hotplate its difficult, i think i ll try with diluiting powder sample with a little bit of water and submerge the thermometer, it can be a reliable way to measure melting point?
