MESO-Rx
Anabolic Steroids
Qingdao Sigma Chemical Co., Ltd (International, US, EU, Canada and Australia domestic
- Thread starter Qingdao Sigma Chemicals
- Start date
Did you heat the oil? Heated is easier to filter. I remember filtering through syringe filters myself and it was the worst part of the whole process.
TyLu17
Member
Did you put an additional needle in the rubber for ventilation? otherwise it will be really difficult
@Qingdao Sigma Chemicals wrote you a email few days ago because of a order.
ZyzzReincarnate
Member
Hey Qingdao,
I'm back from a little ban from the forum. This raws supply catastrophe is tragic. I havent read all of the thread yet so bare with me. Its my understanding that you synthesize your own HGH and some peptides. I dont know anything about synthesizing AAS, but I would think its easier than synthesizing HGH. Could QSC consider synthesizing their own AAS raws and seize this opening opportunity in the supply market to make a profit?
Kind regards.
I'm back from a little ban from the forum. This raws supply catastrophe is tragic. I havent read all of the thread yet so bare with me. Its my understanding that you synthesize your own HGH and some peptides. I dont know anything about synthesizing AAS, but I would think its easier than synthesizing HGH. Could QSC consider synthesizing their own AAS raws and seize this opening opportunity in the supply market to make a profit?
Kind regards.
Unlikely.
Get stronger.
But yea you have a pin to vent as you displace?
Get a hand pump maybe if it's a lot
Yes ofcourse.. but pushing 20 or 30 ml at a time is quite tiring, hence the question.Did you put an additional needle in the rubber for ventilation? otherwise it will be really difficult
rockyraccoon
Member
Caulking gun.
gburdell
Member
Ghoul
Member
And yes, MCT is the least oxidizing of any vegetable oil. When oil oxidizes, its electrical conductivity increases. The Rancimat test heats oil to 120c, and when it oxidizes conductivity shoots up. You can see Miglyol (MCT) easily outlasting the others:
Last edited:
Trenbolonetax
Member
Nice oak hardwood floors, brother. Older construction house?
Trenbolonetax
Member
Ghoul, what is your opinion on Miglyol 840 compared to MCT in terms of health impact? Said differently, any idea on % of propylene glycol in it and the health implications?
If you were going to choose a carrier oil for injectable AAS that isn't MCT and had to be less viscous than MCT, what would you pick?
There isn't any % of propylene glycol in mig840, is an esterified propylene glycol chain. It means it doesn't have the same characteristic of propylene glycol, it's chemically quite different even so it does come from it.
I'm no chemist and so my explanation is retard level but still. Propylene glycol is myotoxic injected, mig840 hasn't shown any toxicity when used IM... But we gotta tell the whole story it hasn't been used for human medicine, at the moment for what I have gathered only veterinary products. Still the tests haven't shown any myotoxicity compared to propylene glycol.
I mean if we wanna be anal, EO on paper is safer, as it's approved in Europe for IM injection in humans and even in the USA it can be used by compounding farmacy for progesterone injection.
Now what would it be the best solution? To not use either EO neither mig840.
That's the truth and I'm saying it as a mig840 lover.
What is the least bad of the two? What are the long term health implication? No one knows I guess.
@Trenbolonetax I made a big edit
Trenbolonetax
Member
Ah okay, super interesting. I jumped to conclusions. My interest is piqued, to say the least, of using it. Not that there is anything wrong with my MCT, but it just sounds incredible to be able to also use less BB and have thin AF oil.
I appreciate the info. Gonna add this to my list of deep dives.
EDIT: Got it; read the rest of your post. I think that's a good point. Ideal to use neither EO nor Mig840. There's just that voice in my head that says it would be so cool to have oil thin like water even though it's completely unnecessary for me lol. As is most of the shit I do.
If you get any good infos, please share.
Yes the combination of less BB (not that it's harmful in the quantity we inject, but it makes any recipes easier if you know that you can use half BB and you use than standard 20%, your gear will hold 110% with no problems).
Is how thin it is that makes the oil fucking amazing tho.
That's the biggest pro of mig840.
Is it worth the risk tho? Fuck if I know and I'm having lots of doubt about it.
Trenbolonetax
Member
I definitely will share!
Yea, it's the thin aspect of it that is so appealing.
I'll add this to my list of "is this worth the risk" questions and then just probably ignore it like everything else. Jk, kinda jk, but half serious.
The thing is... Ok it's thinner, ok it's very nice to be able to inject with 27G with a 3ml syringe and 29G with a 1ml syringe but is it worth your health?
Because we can brew everything we need with just MCT, so the only reason to use MIG840 is for being able to draw and inject with smaller needles.
Does injecting with bigger needles pose an health risk? Not really.
Does using mig840 pose an health risk? Unknown.
It's not hard to decide what do isn't it?
I'll probably use mig840 only for some substances maybe the most viscous one and the one that are very long ester.
Would be nice to be able to shoot bold U 600 for example without an harpoon xD
Maybe a 50/50 mix of mig840/MCT so to reduce the total quantity of it? .
Fuck me man I know what's the right choice, I just like so much the idea of using it ahaha
Similar threads
