Recipe List

Im planing to brew some test. Enanthate,
Anyone tried 300mg/ml with
10%bb-1%ba?
Mct oil
Smooth and painless? Or too high concentration?
 
Never used saff... I always use mct smooth. But not really a good oil to use in hard to keep from crashing compounds, where does one get some safflower oil?
 
Primo E brewed just about like everything else ? Just use calculator and mix, or is there something different with Primo E?
 
Primo E brewed just about like everything else ? Just use calculator and mix, or is there something different with Primo E?

I just made it at 200 and 300mg/ml. The 300 has pip and I would try 225-250mg/ml tops because 200 had the tiniest bit of pip. I used 2%BA, 20%BB migyol for the 200 and EO for 300. Heat only got up to 170, raws went in first then added half of the prewarmed oil,BA, BB mix, added the rest 20 min later. Spent about 30-45 minutes mixing on heat then another 20-30 mixing with heat off to cool down.

Primo seems easy to get into solution like test e, so if you’re a fan of reduced B.B. you can probably do it with 10–15%
 
I just made it at 200 and 300mg/ml. The 300 has pip and I would try 225-250mg/ml tops because 200 had the tiniest bit of pip. I used 2%BA, 20%BB migyol for the 200 and EO for 300. Heat only got up to 170, raws went in first then added half of the prewarmed oil,BA, BB mix, added the rest 20 min later. Spent about 30-45 minutes mixing on heat then another 20-30 mixing with heat off to cool down.

Primo seems easy to get into solution like test e, so if you’re a fan of reduced B.B. you can probably do it with 10–15%

That was what I was looking for, thanks.
 
I just made it at 200 and 300mg/ml. The 300 has pip and I would try 225-250mg/ml tops because 200 had the tiniest bit of pip. I used 2%BA, 20%BB migyol for the 200 and EO for 300. Heat only got up to 170, raws went in first then added half of the prewarmed oil,BA, BB mix, added the rest 20 min later. Spent about 30-45 minutes mixing on heat then another 20-30 mixing with heat off to cool down.

Primo seems easy to get into solution like test e, so if you’re a fan of reduced B.B. you can probably do it with 10–15%

Could I use a percentage of EO and Saff oil in The recipe to help with viscausity ?
 
Anyone done a test 400 blend I was thinking...

150 test e
150 test c
100 test p

Think a Normal 2/20 would work?
Just wing it and see what happens :D... if all else fails just cut it back to 250 and ull basically end up with a sustanon like blend , so it wont be a total loss ... id honestly use eo , but you might get away without it !?
 
No sir. Not a piece. I doubt you'd get test cyp to hold by it's self at 350mg per ml with normal bb percentages and or not using a stronger solvent like guiac. You can add a total of more hormone if you use multiple hormones or esters, but that would be a total not an individual. What i mean is this, and this is just an example. If i could only get test e to hold at 300mg per ml and i could only get eq to hold at 300 mg per ml i most likely could get both together to hold at 400mg per ml (200mg per ml each). But do you see how i had to reduce the individual hormone to get a higher total? So most likely you would only be able to get those products to hold together at 200mg each or less. I have yet to try those 2 together, but that's gonna be pretty close to it.

Is EO required for mast p. Or is BB/BA/GSO fine?
 
What will you be dosing it at? You can actually make Mast P around the 166 mark with just 20% BB but it’ll have some good pip to it.

100 mg/ml. I bit the bullet and ordered the EO. Most likely switching to MCT also because it took me two hours with a caulk gun to run through my GSO brew
 
Back
Top