picholas
New Member
Yeah, 100 and 150 both held with 2/20 in GSO
Try a sample batch of 150mg NPP like 20-30mL and see if it works for you. I'll post up pictures of the whole batched vialed up.
MESO-Rx
Anabolic Steroids
Recipe thread
- Thread starter Robfromga
- Start date
Yeah, 100 and 150 both held with 2/20 in GSO
Try a sample batch of 150mg NPP like 20-30mL and see if it works for you. I'll post up pictures of the whole batched vialed up.
Nice .
I'm making some test c 250 tonight .
Be my first run since making some pellet tren. Hope I don't fuck it up .
250 might be a little aggressive for cyp... You can do it but be prepared in case you need to adjust.
Tips? Was going to only brew 40-50ml.
I've never brewed it that high, so I couldn't say. I would just take it slow to make sure it acts like it is going to hold before putting into vials. Maybe even leave it overnight before bottling.
Test cyp at 200mg isn't hard, but 250mg is getting to the top of spectrum. Enanthate is no prob at that dose though.
XmadXscientist
Member
I make cyp 300 with 22% BB so I don’t have to worry about it crashing, needs more heat to help with the process.
Tren A can hold at 150mg with no EO, EO isn’t some miracle and I don’t think it helps hold much higher at all in my experience. MCT works just as well, most people used GSO before switching to EO so it seems like it holds more because of the viscosity difference is huge vs GSO but not a big deal with MCT.
BB is not some evil thing that causes pip, the high concentration products warrenting increased BB % do that.
Tren A can hold at 150mg with no EO, EO isn’t some miracle and I don’t think it helps hold much higher at all in my experience. MCT works just as well, most people used GSO before switching to EO so it seems like it holds more because of the viscosity difference is huge vs GSO but not a big deal with MCT.
BB is not some evil thing that causes pip, the high concentration products warrenting increased BB % do that.
So it's the high levels of hormone and not the BB that causes pip? To a certain point .
XmadXscientist
Member
Among other things yes. High BA does it, incorrect filters.
XmadXscientist
Member
Time, heat, psi and PH can be manipulated to affect solubility too.
Just 1/20 and MCT?
XmadXscientist
Member
Yeah but I do 125 because 150 causes pip for many people.
XmadXscientist
Member
Tried an expirement today, made primo at 250mg/ml with 1.5%BA, 20%BB, 2% guaiacol and mig 840 as the carrier.
This concentration tends to cause pip in most people and I have a bad habit of pinning 600+mg at a time in one spot. I used guaiacol to see if it would help keep the hormone soluble in the muscle longer preventing recrystalication. I used mig 840 simply because I like it. Pinned this morning so won’t know for a day or two if my theory works.
This concentration tends to cause pip in most people and I have a bad habit of pinning 600+mg at a time in one spot. I used guaiacol to see if it would help keep the hormone soluble in the muscle longer preventing recrystalication. I used mig 840 simply because I like it. Pinned this morning so won’t know for a day or two if my theory works.
The only recipe I'm interested in is TNE and or TrNE.
Discuss.
Discuss.
picholas
New Member
Plate Smacker
Member
Many recipes are regurgitated high percentage recipes that people got from a website, and they used with success, because they work...
Why any one on earth would use 5% BA for a Test E recipe is beyond me, but I have seen them posted.
Many recipes by UGL use same percentages for alot of thier brews. Keeps math and measurements simple, reduces risk of cold climate crashing. Example:Using 2%BA and 20%BB for both test e 250mg/ml and 300mg/ml. Which is insanely high percentages. (NOT SAYING ALL UGL's)
I did not have time to run tests on Tren E to find a working low percentage recipe, so I opted for a recipe I got from a brother on here of 1%BA and 18%BB. It worked, it's pip free. It has a viscosity that I like.
Some of us actually run various small tests to get the best consistency and viscosity, because we brew for ourself and know what we are looking for. However, sometimes the first time brewing maybe you don't have time, and next time you can run tests.
I brewed Test E 300 and Deca 300 with 1%BA and 5%BB. Flows nice, no pip. Pin with 25G.
Test E left, Deca right, Test E Deca blend center.
Tren Ace 1%BA and 18%BB
I was told you can get away with 10%BB, but did not have time to test.
I think these threads would be better if people actually posted pics of the brew they did as well. Also maybe add info on brewing temps, and process. I have the info in other threads I made when I brewed.
Why any one on earth would use 5% BA for a Test E recipe is beyond me, but I have seen them posted.
Many recipes by UGL use same percentages for alot of thier brews. Keeps math and measurements simple, reduces risk of cold climate crashing. Example:Using 2%BA and 20%BB for both test e 250mg/ml and 300mg/ml. Which is insanely high percentages. (NOT SAYING ALL UGL's)
I did not have time to run tests on Tren E to find a working low percentage recipe, so I opted for a recipe I got from a brother on here of 1%BA and 18%BB. It worked, it's pip free. It has a viscosity that I like.
Some of us actually run various small tests to get the best consistency and viscosity, because we brew for ourself and know what we are looking for. However, sometimes the first time brewing maybe you don't have time, and next time you can run tests.
I brewed Test E 300 and Deca 300 with 1%BA and 5%BB. Flows nice, no pip. Pin with 25G.
Test E left, Deca right, Test E Deca blend center.
Tren Ace 1%BA and 18%BB
I was told you can get away with 10%BB, but did not have time to test.
I think these threads would be better if people actually posted pics of the brew they did as well. Also maybe add info on brewing temps, and process. I have the info in other threads I made when I brewed.
Then you set the standard.
I'll filter my cyp and post it tonight, it's held fine at 250 . Hope it's not pip city at 2/20
Johne71
Member
Stir it again thoroughly. The last batch of 250mg/ml of Test C I brewed had some inconsistent crashing. Some bottles crashed while others didn’t. All the same brew. The only explanation was it wasn’t mixed as well as it looked. Looks completely mixed in solution.
J
