Testosterone Suspension without Water

[SUGARBEAR]

Does anybody know how to brew testosterone suspension, as to hydrate it later?

 

[randomdude79]

Well if its not suspended in anything, its just testosterone...To "brew" implies converting it to a liquid, injectable form.

 

[ImHereForBothReasons]

Are you asking how to synthesize testosterone from yams?

 

[SUGARBEAR]

Random: I meant using bb and ba, etc.
Reasons: No. That was a much earlier thread of mine.
How would one brew a non-aqueous blend of hormones, solvents, preservatives, etc as to mix in the bs water later? Worried about infection.

 

[Mr350mg2]

Do you mean test no ester? Its just the same same test you put in suspension only its in oil.

 

[SUGARBEAR]

TestNoEster is the hormone. Yes. I do mean suspension (water). What I am asking is: Do you know a way to brew together all the components minus the bacteriostatic water? Do you filter it? Is it too thick? I am looking to constitute it at a later date. I want to limit as much microbial growth as possible.

 

[SUGARBEAR]

Well if its not suspended in anything, its just testosterone...To "brew" implies converting it to a liquid, injectable form.

I am looking to mix in the bs water at a later date.

 

[SUGARBEAR]

Are you asking how to synthesize testosterone from yams?

No. But, I did a post like that when covid19 hit.

 

[SUGARBEAR]

Do you mean test no ester? Its just the same same test you put in suspension only its in oil.

In water.

 

[Mr350mg2]

In water.

if you mean just mixing the hormone in the solvents I would imagine the alcohol would evaporate unless it was adequately stored in a vial then technically yes you could mix the solvents and hormone in super high concentration then store it in a vial. you could reconstitute it whenever you decided to mix it into the water. As for microbial growth the alcohol will keep the concentration from microbial culture forming.

 

[SUGARBEAR]

if you mean just mixing the hormone in the solvents I would imagine the alcohol would evaporate unless it was adequately stored in a vial then technically yes you could mix the solvents and hormone in super high concentration then store it in a vial. you could reconstitute it whenever you decided to mix it into the water. As for microbial growth the alcohol will keep the concentration from microbial culture forming.

Was thinking that, but alcohol may not kill everything
Filter?

 

[SUGARBEAR]

Just bottled up raw powder with a generous amount of ethanol. Sealed the vial.
TNE & TrNE

 

[Mr350mg2]

Just bottled up raw powder with a generous amount of ethanol. Sealed the vial.
TNE & TrNE

A micron filter would absolutely be a smart idea. The alcohol would only provide one layer of sanitation ideally as many layer of sanitation as possible when your injecting shit in your ass cheek, glutes are an important muscle dont want a doctor digging part of it out to save your life haha good luck hope it works!

 

[SUGARBEAR]

A micron filter would absolutely be a smart idea. The alcohol would only provide one layer of sanitation ideally as many layer of sanitation as possible when your injecting shit in your ass cheek, glutes are an important muscle dont want a doctor digging part of it out to save your life haha good luck hope it works!

Deltoid. Upper body has less risk of infection. Or, so it seems. Also, do you know how they package the “pucks” into the hgh, hcg, or hmg vials? Actual question.

 

[hijoshiki]

There's no reason to take a chance.

I wouldn't inject anything UGL without it being filtered. Water based compounds to me are too risky.

I'd instead dissolve a small amount of raw in benzyl alcohol and then add your DMSO to the concentration you want and need and then use it topically. Same result and much less risk.

Otherwise just make a low dose oil based TNE with BA and BB, skip the solvents and warm it before every use to resuspend crashed hormone.

 

[SUGARBEAR]

There's no reason to take a chance.

I wouldn't inject anything UGL without it being filtered. Water based compounds to me are too risky.

I'd instead dissolve a small amount of raw in benzyl alcohol and then add your DMSO to the concentration you want and need and then use it topically. Same result and much less risk.

Otherwise just make a low dose oil based TNE with BA and BB, skip the solvents and warm it before every use to resuspend crashed hormone.

I’m already doing this. Going to stick the vials the refrigerator. Why do we not, often, treat steroids the same as peptides? This is just an experiment in compounding by different methods.

 

[hijoshiki]

I’m already doing this. Going to stick the vials the refrigerator. Why do we not, often, treat steroids the same as peptides? This is just an experiment in compounding by different methods.

The problem is you're not filtering the product.

Who the hell knows how this stuff was manufactured. For all we know it was done in a cement mixer.

Filtering insures that you're at least not injecting debris into the site that is larger than 0.22 microns which is about 1/4 to 1/2 the size of the smallest cocci bacteria.

You gotta pay attention to the microscopic debris, another reason to use silicone stoppers only when piercing vials to avoid coring.