I call bullshit. You know you reply to emails before wiping the mouth drool off.
MESO-Rx
Anabolic Steroids
Titanium Gear Industries (domestic source)
- Thread starter TitaniumGear (TGI)
- Start date
I call bullshit. You know you reply to emails before wiping the mouth drool off.
brovercleveland
Member
Just a FYI fellas and @Kim Mountainside medical has a 20% off going on with code "dogdays" 
Oh snap, thanks for the headsup on Mountain-Side. They have the Bac-stat Sodium Chloride I've been looking for
Just a FYI fellas and @Kim Mountainside medical has a 20% off going on with code "dogdays"
Im a huge fan of cereal straight out of the box with no milk. Favorites are Frosted Flakes and Captain Crunch. Problem with Captain Crunch is the pieces are pretty hard and they cut up the inside of my mouth pretty good because I am a pig and can’t eat that shit fast enough.
Edit: Now I have to buy a box of cereal this evening
1075gasman
New Member
Does any one have a trick to keep from leaking when pinning? I'm pushing 3ml with 1in and have tried pulling the skin "Z" thing, and also have tried going even slower than I normally do. Or am I just doomed to lose some to the gear gods every time?? (Maybe a stupid question)
T-Bagger
Elite
The Z method fails you? This is unheard of, at least to me! Have you left the needle in your injection site for like 15 seconds after full discharge?
T-Bagger
Elite
Here I thought you were going to contribute and you got me laughing my ass off.
Well, I’ll be on this kick till whatever our new thing is lol
1075gasman
New Member
I guess I may have to explain a little. When I use the Z method it doesn't leak after I pull out. It's as I'm injecting I get the leakage, and like I said I'm going so slow and still leaks while injecting.
Edit: Maybe I'm just a water head and can't do anything right. At lest that's what my wife tells me lol
T-Bagger
Elite
Leaking as you inject? I can’t even fathom this. How deep are you going with the needle and what length are you using?
1075gasman
New Member
Using a 1" needle and I bottom it out before injecting ... guess I shouldn't of asked and looked like a moron
You sure you’re leaking from the site and not from the pin. If you push the air out of the needle you also push some compound out as well. That ends up dripping down the needle towards the barrel. You then pin and the compound rolls off the needle/barrel onto your skin making it look like you leaked.Using a 1" needle and I bottom it out before injecting ... guess I shouldn't of asked and looked like a moron
I do NOT wash plastic dishes. I rinse them before the milk dries.
Emails make me drool.
Never heard of this. Leaking while pinning from pin site? Sounds like pinning concrete. Loosen up that pin site dude.Using a 1" needle and I bottom it out before injecting ... guess I shouldn't of asked and looked like a moron
Somethings i read in other threads make me wanna scream "I told you so!" But imma sit here and have this after nap coffee like a grown up....
Using a 1" needle and I bottom it out before injecting ... guess I shouldn't of asked and looked like a moron
No worries man - I just opened up my left pec today with a 28ga 5/8", something I can easily see and pin. I'd venture to bet it's just the drop or two of oil as you get the air out of the barrel that you're seeing. At least I tend to always see a teeny glisten of oil around the injection site from lubing the pin
MisterSuperGod
Well-known Member
i'm not following. Spoon feed me please.
1075gasman
New Member
The verdict is out your smart and I'm a dumbass. I'm sure that's what's happened never put two and two together.
The verdict is out your smart and I'm a dumbass. I'm sure that's what's happened never put two and two together.
I use the leuger locks (?). I always have to tighten them up before I pin
I read a lot. Just saying some people do things when they clearly know the correct answer. I'm not shaming anyone specifically.
Similar threads
