Unsterile Gear

I am in a similar situation...After I transfer it into a vial I noticed that there were a couple of strands of either cotton or plastic in the solution. Clearly I am thinking im gonna throw it out, but it is a lot of gear (120mls) and I would like to just use it. If I bake it, think it's still safe to use? The strands floating in it are not small enough to enter a needle. What do you guys think?
 
i have received lots of gear in (containers),test and eq., i steril filtered into steril 100mg vials. i have done 3 cycles with every day pokes ,10 weeks each. i have never had the first problem. (knock on wood). i think , it really comes down to steril injection procedure.
 
ThePatriot said:
225 in the oven should be fine. Just dont cook it for too long. 5-10 mins should be good enough. What kind of source is this anyways? I mean shit like that sounds sloppy. Just my opinion


By baking the EQ, he will destroy the hormone {EQ is VERY heat sensitive!}and it will be useless.. my suggestion is to chuck the EQ and tell his source to send it in a sterile vial..
 
Any one got any ideas about my situation? With the strands being so big they cannot be drawn into a syringe. My fear is that they may shed small pyrogens into the solution.
 
ThaRealest said:
Any one got any ideas about my situation? With the strands being so big they cannot be drawn into a syringe. My fear is that they may shed small pyrogens into the solution.

If you are unsure don't use it.. medical bills will cost you more bro.. an abcess if left untreated can result in death..
 
ProLINE said:
If you are unsure don't use it.. medical bills will cost you more bro.. an abcess if left untreated can result in death..


couldnt have said it better. listen to proline, even though you are tempted to use the gear and save a little $$$. in the long run you'll be thankful.

Skywalk
 
To me its to much to buy gear then have to bake it, filter it add BA whatever even if it to ship internationally, although some domestic UG labs you have to dosame thing (I won't mention any names)-no one should have to go through all that I know it is cheaper because basiclly you have to work at your gear to assist in a final product where as a little extra cash you can save yourself time, aggrevation and possible as mentioned before medical problems.
 
Yea I agree with that!
I'd rather order my own EQ power and make my own, rather than to use that EQ...

But let us know if you are o.k...
 
decided not to use it -- its my first cycle, the Test and Dbol should be good enough first time around. I've still got time for many more cycles -- no need to risk my health, especially on the first one. Thanks again for the input, guys.

Nevr2Big
 
EDED said:
talon you must work at a lab, me too, anyways, some pyrogens are small and will go right through 0.22um



like everyone else said, bake, filter, add ba, then shoot maybe a cc or 1/2 cc just to see if you get an infection or not then go all out.

Just some technicalities for future reference...
Viruses will go through a .22 micron filter, although there is little possibility you have to worry about viruses. Pyrogens, which are primarily cell wall components of bacteria, will fit through .22 micron filters too.
There would have had to have been a lot of bacteria present to leave enough pyrogen behind to worry about. To heat inactivate pyrogens, you have to bake at 180 degrees C (too lazy to convert) for a min of 90 min.
An additional note...baking a vial (empty) to sterilize it is fine....crank up the heat. It's no problem....the heating makes the oven a sterile environment too,
By the way, testosterone's melting point is 325 degrees F, but play it safe and stay at 250 degrees or below.
 
Glad to see that your going to just not use it. Most people are not willing to lose that kind of money and would have tired it out.
 
it was easy to decide not to use it since I didnt pay for it -- I wish I could say I would have made the same decision had I actually invested $$ into the product.

Keep Growin,
Nevr2Big
 
Back
Top