Nick9
New Member
Would you say, ten weeks in on bloods, or sooner?
MESO-Rx
Anabolic Steroids
24k Pharma US Domestic Source
- Thread starter 24kpharma
- Start date
Would you say, ten weeks in on bloods, or sooner?
michaltyler
New Member
5-6 weeks for bloods
bparmy11b
New Member
6 wks is sufficient. 24-48 hrs after last pin. And I would pin twice a week instead of once to keep your bloods stable.
Bighead101
Well-known Member
Always filter. Doesn't matter if it's your gear or another ugl
Hey Meso community,
I wanted to address the sterility concerns brought up. I am confident that my product will not cause any issues in regard to sterility but I also understand the "safe better than sorry" sentiment. As a result, I am considering offering sterile syringe filter + sterile vial packages in the near future if there is a demand. Would this be something the community is interested in?
I wanted to address the sterility concerns brought up. I am confident that my product will not cause any issues in regard to sterility but I also understand the "safe better than sorry" sentiment. As a result, I am considering offering sterile syringe filter + sterile vial packages in the near future if there is a demand. Would this be something the community is interested in?
I'm sure your confidence will prevent any "sterility issues"...
I am seriously laughing out loud... it's like I am about to fuck a chick and I hand her some herpes medication - "I am confident you won't have any issues sweetie, but hold on to this".
What a fucking joke. Good luck with that.
hotdog23
New Member
If they are "complimentary"
Nick9
New Member
Alright, I had to boil the water to get it to liquefy, and dissolve. I put in a box in my room over night, and slugged back up the next day. It can't be freezing in my room. Haha. I googled, and theirs lots of conflicting views. Will I have to boil it every time?
Gramps
New Member
I read where 24k was having some issues and upped his BA to 5 or 6%, unlike other sources. I don't remember if that was a suspension issue or not, but I believe it was since he is one of the few admitting to dosing problems and dosing around 320 to reach the advertized 250. I give him credit for at least making an effort, I just question the higher BA plus the crashing gear you're showing.
Ug. That looks ugly. Not sure I'd pin that. I'd ask for replacement.
hotdog23
New Member
Lol yes depot can crash. Will hurt like hell, less likely as your body is warm
Nick9
New Member
Also, I checked out whatman .2 syringe filter on Amazon is $190, and they have some off brand pack of 25 for $22.95. Dayum! That is a big difference. Any advice here? I do apologize for the many questions. I'm new to trt, and I really don't trust any other forums after finding this one.
midland412
New Member
Check gpzservices dot com
They have .2 Whatman filters for $5.50 each. Are you familiar with how to filter gear?https://thinksteroids.com/community...ier-for-needles.134362148/page-2#post-1212439
Use a .2 filter instead of the .45 listed. Also a 20 inch needle to draw and inject will suffice. You can get all of the necessary supplies from GPZ.
They have .2 Whatman filters for $5.50 each. Are you familiar with how to filter gear?https://thinksteroids.com/community...ier-for-needles.134362148/page-2#post-1212439
Use a .2 filter instead of the .45 listed. Also a 20 inch needle to draw and inject will suffice. You can get all of the necessary supplies from GPZ.
Last edited:
Yes, I have had some customer report that they have to re-warm it up everytime. Others have said once it is uncrashed then it stays uncrashed, and finally come have had it not crash at all. I am uncertain for the reasoning.
Here is picture of crashed vs uncrashed Test C: https://img.bi/#/NH1AsDV!DIQtzJzALDKNcdkFXeAtRErSvBZSzwIpemxHxqz2
Here is a picture of the crashed Test C warmed up and the uncrashed Test: https://img.bi/#/Zx3hgWC!OXmT4tgcoGzvzpOclAZ9xd2DA42UysUE1hjrBBv3
As you can see, they look almost identical after warming it up. Furthermore, I have not had any reports of bad PIP from the crashed Test C. I am happy to link you to a public review that also supports this!
Nick9
New Member
Shit, not really. I would've been searching the homebrew section on how to filter. Haha. Thanks for the heads up on gpzservices. Is that the same as getpinz.com?
Great observations, in the batches before this I upped the BA to 6% (I will have to double check this) and the Test C held. But the most recent batch is brewed at 2%, I am happy to link the post where I discuss this, however it is on a different community. I believe this lower BA is one of the reasons the Test C at "250" is not holding well.
Here is a photo of product from that batch after warming it up in a hot water bath (the vial with the water is the crashed Test C): https://img.bi/#/Zx3hgWC!OXmT4tgcoGzvzpOclAZ9xd2DA42UysUE1hjrBBv3
That is something I can definitely consider. I will just need to relook at the logistics as I believe each vial bought would have to come with an additional empty vial to transfer into as well as the syringe filter and a 10mL syringe. Furthermore, how many mL do you recommend for each syringe filter? Thanks for the comment.
Thanks for the reply. While admittedly there is no way I can guarantee 100% sterility of product, especially in a non-pharmaceutical setting such as myself, I have not had any reports of sterility issues thus far. I can understand the sentiment, however.
