MESO-Rx Sponsor Axle Labs - US Domestic

[FastBun]

Look Ma, Axle still doesn't test his raws.

But why would he… look how good his numbers are!!
Test-E (250mg/mL) -> 275.74 mg/mL
Mast-P (100mg/mL) -> 112.68 mg/mL
Pfff… a blind infant could probably tip the raws over and be more accurate…

Also… he keeps acting stupid and rephrasing your question… he keeps ignoring what you are asking in regards to heavy metals being stuck… he acts stupid and claims he doesn’t use a metal stir rod…

 

[FastBun]

You have never observed any metal particles on the stirrer bar at the conclusion of your 0.5 or 1 L batches similar to what was shared in the picture from the other vendor and another picture shared by a member?

lol you really think he pays attention to that considering his brewing practices and test results???

 

[Axle Labs]

You have never observed any metal particles on the stirrer bar at the conclusion of your 0.5 or 1 L batches similar to what was shared in the picture from the other vendor and another picture shared by a member?

I truly have not. If I just didn’t notice that, it’s possible but I feel I would have noticed that since it would stay on the stirrer if it was a metal particle.

If it didn’t stay on it, it would get caught in filters.

Regardless, we’re asking for both sterility and metals testing, like I said. It seems the demand for metals testing is low but we’ll do a metals test on a compound.

 

[readalot]

I truly have not. If I just didn’t notice that, it’s possible but I feel I would have noticed that since it would stay on the stirrer if it was a metal particle.

If it didn’t stay on it, it would get caught in filters.

Regardless, we’re asking for both sterility and metals testing, like I said. It seems the demand for metals testing is low but we’ll do a metals test on a compound.

I can believe this. The vendor who shared the pics mentioned he didn't start to notice the particles until he scaled up batches to higher than 500 g of raw. 750-1000 g of raw they were very noticeable for Test E and Test C.

Correct, the metal particles would only be issue for orals / unfiltered products using raws.

 

[Axle Labs]

I can believe this. The vendor who shared the pics mentioned he didn't start to notice the particles until he scaled up batches to higher than 500 g of raw. 750-1000 g of raw they were very noticeable for Test E and Test C.

Correct, the metal particles would only be issue for orals / unfiltered products using raws.

Gotcha. No unfiltered oils being sold on our end.

Orals, we’ll do a metals test.

 

[readalot]

Gotcha. No unfiltered oils being sold on our end.

Orals, we’ll do a metals test.

If you want to isolate the metals for ID, you have to have a way to separate them. It appears they are heterogenous and at low concentration in the raws so that's where the efficient method of separating them in the oil batches magnetically comes in handy.

Their yield is dependent on raw amount. You won't be able to pick them up via Jano's test by sending in a raw powder sample he ask for. If you ever scale up and see the magnetically captured particles. Put them in a vial, send out and then Jano may be able to analyze what they are.

 

[Axle Labs]

If you want to isolate the metals for ID, you have to have a way to separate them. It appears they are heterogenous and at low concentration in the raws so that's where the efficient method of separating them in the oil batches magnetically comes in handy.

Their yield is dependent on raw amount. You won't be able to pick them up via Jano's test by sending in a raw powder sample he ask for. If you ever scale up and see the magnetically captured particles. Put them in a vial, send out and then Jano may be able to analyze what they are.

Thanks for the info. If I ever notice the particles, I’ll be sure to collect and send.