Big Bear Labs U.S. Domestic

Why not? If I’m doing everything else in there why not do that as well? It just makes everything easier if I do it all together instead of spreading it out all over.

[emoji23] You want us to believe that you went from syringe filtering batches you made on your stovetop into pre-sterilized vials to making everything in a hood, even the steps that are dumb to do in a hood because they’re messy (powders and measuring correct ml of BB/BA)

So you set up your flirtation assembly in there too then?

And then you clear that out and you slide your freshly claved vials in and measure out 10 ml with a pipette while wearing those rubber gloves?

Really Big Bear? Like for reals?? I think you’re going down the wrong story path here.
 
I’ve never syringe filtered not sure where you got that info. I’ve always used autofil vacuum filters. I use a 60ml syringe to dispense into the vials. When my dispenser with inline filters arrives it’ll be much simpler and easier with the crimper as well.
 
You were asked in the beginning for pics of your flow hood. You acknowledged on Pg 1 that pics needed meso/crumpled paper. You finally produce pics of one you're apparently using on loan by your own words. So you've proven your full of shit and your trying to drag your feet through this so you can get proper equipment or scam I haven't decided which yet.

Either way you're full of shit and anyone who's been here more then a week sees what's going on.
 
I didn’t realize every pic with everything needed it. I’ll take more pics for you. Honestly I doubt most even use a hood it’s unnecessary but I always like to go a little further than is needed.
 
[emoji23] You want us to believe that you went from syringe filtering batches you made on your stovetop into pre-sterilized vials to making everything in a hood, even the steps that are dumb to do in a hood because they’re messy (powders and measuring correct ml of BB/BA)

So you set up your flirtation assembly in there too then?

And then you clear that out and you slide your freshly claved vials in and measure out 10 ml with a pipette while wearing those rubber gloves?

Really Big Bear? Like for reals?? I think you’re going down the wrong story path here.

You beat me to it. Pushing sealed sterile vials when he has a semi-professional looking setup at his disposal?

i'm calling bullshit on this. This lab of his is probably on a college campus where he has sporadic access to it, which would explain why it took so long to provide proof.
 
Do it or dont, anyone looking for a source will hopefully read this thread and keep it moving. Nothing in this thread points to a solid source and it would be nice to add a couple.
 
You beat me to it. Pushing sealed sterile vials when he has a semi-professional looking setup at his disposal?

i'm calling bullshit on this. This lab of his is probably on a college campus where he has sporadic access to it, which would explain why it took so long to provide proof.

He should have taken the stupid scale out. Can you picture carefully measuring powder with those fucking gloves on. Oops 0.5 gram over, carefully remove. Ok good. Transfer to beaker. Now measuring the BB? Can you hold a graduated cylinder with those gloves. I’d go fucking crazy. And then you spill and your clean hood area is a mess that you need to thoroughly clean up. Instead of simply wiping a countertop??

And there’s NO reason to do any of that since the brew doesn’t have to be sterile until AFTER filtering. So all the clunky black glove work would be maddening real quick.

He tried covering up his scale mistake with a bullshit story. There’s plenty of space in the rest of the room for the non-sterile work.
 
Because you wouldn’t do it doesn’t mean I wouldn’t do it. Yes things may be a little harder but I’d rather do everything under the hood from start to finish.
 
One love that you called me kodiak two there’s a reason why I’m getting my own hood as well that’s just a sliding door hood without the gloves. Cost is approx $2k. Will also be buying a an auto pull capper but again that’s another $2k-5k. Yes somethings are harder to do until then but I do everything I can to keep sterility and consistency top values.
 
Listen little bear, if you’re making this shit in the most cheap cut corners way you might as well own it.

if you’re telling me you can only synthesize when you have access to this hardware that tells me you’re just venturing into this without much if any overhead.
Whatever that’s fine if it’s just for you or your gym buddies or whatever. But if you’re seriously using this as an income that’s not going to cut it.

You can learn a ton here, maybe ya know use your reading comprehension skills and pick up some knowledge here. Admit you’re learning, admit you don’t really know wtf to do, admit you need guidance.

Although, that requires humility, honesty and integrity which I’m guessing aren’t your star qualities so far.


Edit: post above me just confirmed all of this.
 
Venturing in without much overhead is a much smarter business move. It’s like renting a space before investing into buying a commercial property. The products I am selling are sterile and made correctly. Yes I am upgrading and going to have my own space completed shortly as well.
 
Because you wouldn’t do it doesn’t mean I wouldn’t do it. Yes things may be a little harder but I’d rather do everything under the hood from start to finish.
Damn dude, took you weeks and a day to post that pic and you conveniently left out the Meso paper and date... smh.

Your stories aren’t adding up to most members that’s posting in here. Including myself!

This is why you should have all your shit together before coming here!
Now instead of having something to build on by coming in prepared, you come unprepared and keep digging a hole for yourself. Pretty soon the hole is going to be so deep we’ll start covering you... and that’ll be the end of Big Bear.

Currently I see you as an unprepared source that doesn’t follow basic requests to include the Meso pic and date. So that makes you look, to me, that you are lying about the hood and probably your whole operation.
Come to think of it, I liked you better when I thought you were syringe filtering... that was more believable that the last few things you posted.

Shut down your shit. Regroup and get everything you need to make this work in the most professional way possible. Get your flip tops and crimpers, your fancy labels, your flow hood all together then brew and cap that shit.
Come back to this thread as a new source with everything you’ve already been asked for and ready to provide it. Maybe you can add your sterile vial brew as a bonus to your new brew with orders to bring in customers?
I already know you won’t do that and I will watch as you slowly keep failing and eventually fade out.
 
I’ve been brewing for a few years now and have sourced locally. I’m moving to a larger frontier and I know how/what to do. Slowly upgrading everything as we go but as I’ve shown and said we do everything step by step correctly to insure sterility.
 
I’ve been brewing for a few years now and have sourced locally. I’m moving to a larger frontier and I know how/what to do. Slowly upgrading everything as we go but as I’ve shown and said we do everything step by step correctly to insure sterility.
So honestly, tell me what equipment you have, and have been using to source locally?
Lying literally gets you nowhere. If you’re syringe filtering and all that shit, cool. Tell us. Say “I’m new and want more money, here’s the basic ass shit I use to brew me and my handful of customers now”
 
Back
Top