MESO-Rx
Anabolic Steroids
BrewPorn
- Thread starter Leancuisine
- Start date
-
- Tags
- shnozzberries
superbane
Well-known Member
Prepared for the apocalypse
thanks again m8, by any chance you got any smooth recipe for test enanthate 300mg and trenbolone enanthate 200-250mg?
for test. enanthate i got pipless recipe 300mg - 1%BA/15%BB
I have not tried to brew trenbolone enanthate yet, so id like to know if ill hold with same ratio...
Last edited:
I wasn’t able to get my tren E to hold at 15 percent. I would just go right to 1/18 as long as you keep it under 250. Closer to 300 and you might have to go to 20.
Slammich
New Member
I have only done tren e at 200. I'm not a fan of "how much will it hold" because i use what i brew and pip increases with concentration. Never pinned anything i made that hurt yet so I stay to what i know is good for me.
Now test e @ 300 is easy. Check my recipe thread.
picholas
New Member
Just 140mL of Dbol Inject @60mg/mL 
If it holds bottle and capping it tomorrow
If it holds bottle and capping it tomorrow
G2Ready
Well-known Member
Stepping away from the caulk gun and joining you big guys
Y’all ever use a 250Ml GL45 media bottle to catch the zap cap .... or is it to short?
What’s up with the auto fill filters?..just has a screw connection for media bottle?
Y’all ever use a 250Ml GL45 media bottle to catch the zap cap .... or is it to short?
What’s up with the auto fill filters?..just has a screw connection for media bottle?
picholas
New Member
Not sure what you mean by "too short" the threading has to match up. Some bottle top filters don't even have threading and just operate on the vacuum seal.
Size of the catch bottle won't matter, unless you're putting 400ml in a 250ml bottle.
I've used the EMD millipore and fox before . I think the EMD were slightly better .
G2Ready
Well-known Member
^^^wondering if that bottle would go with that filter
It’s hard to tell height of bottle, compared to size of filter
(Only having dealt with picture only)
picholas
New Member
Fits 33/44mm and this is one of those no thread ones, fits both because it works on the vacuum not the threads.
G2Ready
Well-known Member
Threads worth it?.... notice a difference
Most pics I’ve seen are people with a 1,000 or 2,000 ml bottle
Didn’t know if my 250ml was to small
(I just been doing 100ml) at a time— but sick of sitting there
G2Ready
Well-known Member
Where would one get the emd milliliter from?
picholas
New Member
Threads worth it?.... notice a difference
Most pics I’ve seen are people with a 1,000 or 2,000 ml bottle
Didn’t know if my 250ml was to small
(I just been doing 100ml) at a time— but sick of sitting there
I actually prefer the Whatman no thread to the Nalgene and Autofil. Haven't used Millipore. When I was using bottle top 250 or 500mL is plenty. The filters can only safely filter about 700mL I think anyway.
Nope, threads don't really do anything.
G2Ready
Well-known Member
Awesome!!
Before you guys where autoclaveing and bottle/& crimping
What’s a better (or is there?) way to transfer from filtered to pre sealed vial
Before you guys where autoclaveing and bottle/& crimping
What’s a better (or is there?) way to transfer from filtered to pre sealed vial
Gpz has them . Heck, Amazon has them I believe
G2Ready
Well-known Member
G2Ready
Well-known Member
Appreciate the help bros
I’m far away from dealing with autoclave
But could y’all use something like this?
I’m far away from dealing with autoclave
But could y’all use something like this?
picholas
New Member
I wouldn't those are converted pressure cookers. I mean I guess it would get the job done. But not a fan personally. I would pick a brand name and wait for a good bargain.
That's them .
Just make sure you use a glass media bottle.
Personally unless you're brewing 200-300+ a caulk gun and 60ml barrel are pretty quick .
