Did you try other types of oil?
I know that oil features influence pharmacokinetics, so I imagine you rely on castor because of more stable blood levels and more constant release from the depot.
MESO-Rx
Anabolic Steroids
First time homebrewing
- Thread starter 19nor
- Start date
I know that oil features influence pharmacokinetics, so I imagine you rely on castor because of more stable blood levels and more constant release from the depot.
narta
Member
Why isn't worth it?
No I didn't. My body agrees with castor oil so I never though on changing it.
How do you manage the viscosity? I mean both during the brew and when injecting, needle gauge used, time to push/inject.
Thanks
narta
Member
The higher bb thins it out a bit and I filter while it relatively hot (~70 Celsius).
I warm it on a mug warmer before injection, 21g to draw and 23g-25g depending on injection site. 1ml goes slowly at 30"
Denicnut2427
Member
High mg concentration aren’t really supposed to be made…you might need some ethyl oleate I don’t like using that and there is just no need for 400mg Or higher or making crazy blends…250 or 300mg test is plenty…I did a blend of 200mg test cyp with 100mg of test prop per cc that worked well but I wouldn’t go higher than that…half ml 4x per week is plenty on a cycle
No need for eo in test d at 400 mg.
There is a need for some people including myself for 400 mg test. And if it can be done I use that.
For you it might not be a need but world isn't all about you. Isn't a one size fits all.
That's why is Fanta and Coke. For people to choose what they want.
That's why is higher and lower concentration. For people with different needs and preferences.
But you can't say Fanta sucks and no one should buy,it should be stopped from production because I don't drink it.
narta
Member
.
I can blast with 3cc per week. That's convenient too.
There is need for high concentration gear: less volume per injection. I can inject .5cc every 10 days. That's convenient.
I can blast with 3cc per week. That's convenient too.
Denicnut2427
Member
It’s just my experience and of many other that you have to use extreme solvents and then if the high mg does stay suspended and you shoot it it knots up or causes pip or just doesn’t absorb right at all and really no one needs to have to shoot 1500mg of test in 3ml…I highly doubt you’re a 300lb bodybuilder competing in meaningful competitions and honestly the ones that I know that do keep there test at 750-1200mg and rotate and anabolic at 300-600mg per week in the off season and during contest prep it’s a mix of more drugs and actually lower doses of all of them that would be used any other time…so you’re half ml cruise??? 3ml blast chances are the shit isn’t even absorbing right it’s just another thing for drug abusers of steroids to think they need and know about…I remember when people first started getting test 400 mg from denkall
Your experience and many others is misleading you then
But it's ok you don't hsve to do anything that I and narta or others do.
narta
Member
Do you homebrew?
Test D is usable at 400mg/ml with no extreme solvents. So it's 500mg/ml EQ. No knots, no pain, no nothing.
And yes I cruise on 200mg every 10 days. One .5cc shot.
But, you do you. I will continue to experiment with homebrewing my own after 2+ decades of doing so cause I like it and so will many others.
Denicnut2427
Member
Yes I do and I’ve made test enth at little over 350mg no problem and I know eq can go rather high and even deca to a point but just bc it holds doesn’t mean it smart to do that’s all…the eq I would run high I can see putting that at a high mg…I just know people that try to make a 200mg npp or a 200mg tren ace it’s just fucking crazy…but you’re right people can do what they want to thier bodies if someone runs 2g of test and want to do it in 4ml fuck it I just don’t think that’s good info for someone new to steroids or home brewing and it’s just really not necessary
GORDON RAMSAY
New Member
what about rubber sterilization?
Keebler12345
New Member
I soak them in alcohol
Astartes
Well-known Member
Honestly.
Biggest recommendation I can make for guys going to home brew is STOP trying to use syringe filters. It is a nightmare mess. Go to bottle top vacuum driven. 2 small pumps and run through .45 then .22
You will never go back
Biggest recommendation I can make for guys going to home brew is STOP trying to use syringe filters. It is a nightmare mess. Go to bottle top vacuum driven. 2 small pumps and run through .45 then .22
You will never go back
I don't plan to homebrew frequently, but sounds interesting. I never gave attention to the precise steps of using bottle top vacuum for this reason, but may I ask you some more info about it? Like, time to get familiar with the procedure, cost of investment, time needed to filter this way, etc...
Thanks
Astartes
Well-known Member
Traveling this week so I don’t have a lot of time to elaborate. Tons of info on this forum and across the net. ~$200 to get set up with basic filtration which works for 99.9% of folks not running commercial ops. Much simpler than syringe filters.
Keebler12345
New Member
I could not agree more
Completely messed my first homebrew with serynge filter
Will try once again. Will go bottle top if it is again a mess
narta
Member
I have been homebrewing for 2 decades with syringe filters and after the initial learning period (busted filters from too much pressure) I have yet to screw up a brew due to filtering.
What is so difficult?
What is so difficult?
Do you use the caulking gun or do it just by pushing the plunger of the syringe by hand?
Similar threads
