master.on
New Member
Is it?
MESO-Rx
Anabolic Steroids
Is it possible to completely remove estradiol from Trenbolone implants?
- Thread starter master.on
- Start date
Mitchy99
New Member
U will need to filter many times and recrystalize many times to remove it check melting points should melt around 201° to 206° if estrogen is present it'll be a lower melting point
Ripped
New Member
Lmao
Mitchy99
New Member
Component th is recalled they quit making it without estradiol. It was to easy for home brewers to make so they had to make it harder for us
Since when...I just made some in April
Mitchy99
New Member
So did I but went to make more like 2 months ago. They were outta stock so I did some research and found an article about it
Yea that has come up several times over the last 12 years. I’m sure it will be back..
Mitchy99
New Member
I sure hope so next time it comes back (if it does) I'm going to buy a ton of it
master.on
New Member
Interesting
Does it become water soluble with Sodium hydroxide?
Estradiol has 2 hydroxy ( -OH ) groups, that might be converted to Sodium salt, although not as efficient as neutralizing a carboxylic acid
While Tren has an -OH group, it is "used up" by the acetate ester
You'd need at least 40 mg Sodium hydroxide for every 272.38 mg estradiol
Interesting
Does it become water soluble with Sodium hydroxide?
Estradiol has 2 hydroxy ( -OH ) groups, that might be converted to Sodium salt, although not as efficient as neutralizing a carboxylic acid
While Tren has an -OH group, it is "used up" by the acetate ester
You'd need at least 40 mg Sodium hydroxide for every 272.38 mg estradiol
Correct it becomes water soluble. I don’t remember all of the math and complexities. This was 11 years ago.
The process is a pain in the ass. I remember that much lol
master.on
New Member
Does this sound like a reasonable procedure?
Do you think I'm missing something?
1 Crush implants
2 Pour in water + Sodium hydroxide
3 Stir for a while and let it sit undisturbed
4 Draw water at the top, keeping the precipitate at the bottom
5 Rinse the precipitate with water, while on a filter
estradiol should be gone in water, so should Sodium hydroxide and some fillers
6 Allow to dry. Warm a bit if needed
7 Pour in oil
8 Stir for a while and let it sit undisturbed
9 Draw oil at the top (with Tren in it) and leave the precipitate with fillers
10 Add BA, BB, sterile filter and pour in vials
11 Inject and enjoy.
I know that was ages ago, but does it sound about right to you?
Thanks a lot
It’s more like this:
-Dissolve implants in 250ml of methyl alcohol (HEET)
-add sodium hydroxide / water solution
-let sit for 45min to salt the estrogen
-SLOWLY add 500ml of very cold water, let sit for 30min
-filter out crystals that formed and set these aside
-add another 250ml of cold water to the previously filtered water
-filter out any new crystals and set aside
-rinse all crystals with 1 gallon of water
-allow to dry for 48hrs
-brew it up
I don’t recommend this bro
Even tho I don’t endorse this at all I am indeed a sucker for sharing knowledge / experience... here is a very informative link
https://thinksteroids.com/community...novex-component-eh-can-be-purified.134365979/
https://thinksteroids.com/community...novex-component-eh-can-be-purified.134365979/
master.on
New Member
Thanks a lot for the info
As for the reasons why
I can get lots of cheap Revalor implants
I love the chemistry challenge.
