My NPP-200 recipe

[Deleted member 127229]

I would like to share a recipe I had success with. it's a high milligram brew.

NPP 200MG/ML

2% BA
23%BB

In mct


I used a bit more heat to go into solution, 170F on magnetic stirrer. Filtered at 125F.

Pretty fluid at room temperature, I can draw it with a 25g at room temp. But warming it speeds it up greatly.

holds at 65F no problem, few days now.


I put it in the fridge for 2hrs and no crash.

I pinned it today. 1.5ml in the delt, zero pip so far. if any pip I'll update but I doubt it.

 

[DECLAN]

I would like to share a recipe I had success with. it's a high milligram brew.

NPP 200MG/ML

2% BA
23%BB

In mct


I used a bit more heat to go into solution, 170F on magnetic stirrer. Filtered at 125F.

Pretty fluid at room temperature, I can draw it with a 25g at room temp. But warming it speeds it up greatly.

holds at 65F no problem, few days now.


I put it in the fridge for 2hrs and no crash.

I pinned it today. 1.5ml in the delt, zero pip so far. if any pip I'll update but I doubt it.

Thanks bud, like I mentioned in some guys thread, I brewed it at 150mg at 18%bb and it held well. I will try your recipe with my new powder from QSC, I was just finishing old raws from another source on my first brew.

 

[klokke23]

I made mine at 150. Can't remember if I used 18 or 20. But that crashed after a couple of weeks in my room. Often had to reheat it before pinning.

 

[Deleted member 127229]

I made mine at 150. Can't remember if I used 18 or 20. But that crashed after a couple of weeks in my room. Often had to reheat it before pinning.

Are you using gso or mct? In mct at 2/20 I brewed npp at 150 and it held great.

 

[klokke23]

Are you using gso or mct? In mct at 2/20 I brewed npp at 150 and it held great.

Mct.
Room went no colder than 15 Celsius I think. But I recall seeing reports that 175 crashes at 2/20. So 2/20 holding 150 is probably not by a huge margin.

 

[klokke23]

10g Tren A - 100 mg/ml, 20/2 MCT
10g Mast P - 100 mg/ml, 18/2 MCT
10g Test P - 100 mg/ml, 18/2 MCT
16g NPP - 150 mg/ml, 18/2 MCT
10g DHB - 66 mg/ml, 20/2 MCT

All went well. Tren almost fully dissolved at room temp, finished it in shallow water bath around 40°C.
I tried to dissolve the other brews by leaving them in the cupboard overnight. No luck. I put them in my frying pan at 50-60 °C and they dissolved quickly.

12v vacuum pump. And 1A DC supply.
View attachment 162488View attachment 162489

Apparently I brewed it at 18/2

 

[MfgEng]

I would like to share a recipe I had success with. it's a high milligram brew.

NPP 200MG/ML

2% BA
23%BB

In mct


I used a bit more heat to go into solution, 170F on magnetic stirrer. Filtered at 125F.

Pretty fluid at room temperature, I can draw it with a 25g at room temp. But warming it speeds it up greatly.

holds at 65F no problem, few days now.


I put it in the fridge for 2hrs and no crash.

I pinned it today. 1.5ml in the delt, zero pip so far. if any pip I'll update but I doubt it.

This recipe should hold test e/c/d at 400mg/ml as well. Same thing with the heat to hold.

 

[Deleted member 127229]

Just wanted to update. My npp 200 hasn't crashed, no pip, and it's pretty fluid at room temperature.

 

[MfgEng]

If you put a vial in the fridge and it does not crash then there is a good chance the exact same technique will accept 250mg/ml. If you try it let us know

 

[Deleted member 127229]

If you put a vial in the fridge and it does not crash then there is a good chance the exact same technique will accept 250mg/ml. If you try it let us know

I may try that next time but it won't be anytime soon. Because I still have like 75ml of npp-200. I'm enjoying using less oil for sure though.

 

[Disarmer]

Thanks for sharing, I'm pretty surprised this is holding for you without super solvents. QSC?

 

[Deleted member 127229]

Thanks for sharing, I'm pretty surprised this is holding for you without super solvents. QSC?

Yeah the raws were from qsc

 

[MfgEng]

I'm pretty surprised this is holding for you without super solvents.

A BA/BB solution can hold a lot of concentration of typically injectable compounds. If the heat during brewing is around 190 even propionates will hold at 200mg/ml. Test D I did at 400mg/ml and feel good I could have gotten 500mg/ml as it just snapped right into solution well below 190. Even dbol is possible without super solvents

 

[y777]

Has anyone tried brewing 250 NPP in castor ?