ve79
Member
It fucking stings like no other . I stopped after 9 weeksPrimo200 can be very nasty. I’ve been lucky so far with other vendors. Never had the chance to try opti.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
It fucking stings like no other . I stopped after 9 weeksPrimo200 can be very nasty. I’ve been lucky so far with other vendors. Never had the chance to try opti.
did you try mixing it with something mild like test cyp 200? That's what I've done and it's been ok. Still has some kick but it's tolerable. Never went with P200 alone in the barrel.It fucking stings like no other . I stopped after 9 weeks
I’ve used quite a handful of the primo 200 vials never had any issue with gso, or mct never heated it either.It fucking stings like no other . I stopped after 9 weeks
Diluted mine down to 140ish....couldn't handle the PIP and goose egg.It fucking stings like no other . I stopped after 9 weeks
Definitely still has PIP. But it’s tolerable. No bumps, goose eggs, anything, just mild discomfort at inj siteIt fucking stings like no other . I stopped after 9 weeks
Mug warmer is a great investment. Got it out of necessity for using TNE with no super solvents, but started warming everything up just to speed up the process as I use smaller gauge needles than most for drawing and injecting. Never struggled with pip on anything bad enough for it to be an issue for me personally, but that's definitely going to be another benefit of using a mug warmer for many.my opinion is the PIP from primo (and its non-C1 methylated parent DHB) is from poor solubility and formation of invisible microcrystals that are drawn up then injected. They can be a nidus for bigger crystals to coalesce, ie crash. Few min on a mug warmer has fixed this for me every time. At room temp those microcrystals basically form a suspension and they irritate/inflame then muscle (or fat if given SiubQ). Diluting helps too, but I’d still warm them up. Once inside the muscle the microcrystals won’t recur at 98-99 degrees, but they will at room temp during storage.
What’s your go to mug, Warner?Mug warmer is a great investment. Got it out of necessity for using TNE with no super solvents, but started warming everything up just to speed up the process as I use smaller gauge needles than most for drawing and injecting. Never struggled with pip on anything bad enough for it to be an issue for me personally, but that's definitely going to be another benefit of using a mug warmer for many.
mr coffeeWhat’s your go to mug, Warner?
I just looked for one on Amazon that had a few temp settings. I use 131° on the one I got, which is its lowest setting.What’s your go to mug, Warner?
Everything is out lolGold’s are out
Not on website? Only thing out is goldEverything is out lol
Never experienced using one. Do you just heat up your oil in the syrnge when you injection or the vial?Mug warmer is a great investment. Got it out of necessity for using TNE with no super solvents, but started warming everything up just to speed up the process as I use smaller gauge needles than most for drawing and injecting. Never struggled with pip on anything bad enough for it to be an issue for me personally, but that's definitely going to be another benefit of using a mug warmer for many.
In general. Not ghNot on website? Only thing out is gold
Just set your vial(s) on the mug warmer until the oil is warmed up, or, in the case of things like TNE that crash, until everything is back in solution again. Then draw everything into your syringe and inject.Never experienced using one. Do you just heat up your oil in the syrnge when you injection or the vial?
That's exactly what I do... I use B-D 31g 5/16" 0.5cc insulin pins for everything, they're the sharpest and best. TNE w/o solvents, DHB, and Primo go on the warmer every time for a couple min. Used to do mostly subQ injections but finally got lean enough where I switched all oils to IM. I alternate biceps, triceps, pecs, delts, hip flexors, and quads. Still have a bit of fat on my ass and love handles so do water-based injections there subQ (L-carnitine, GH, Reta, IGF1-LR3, Selank/Semax, BPC157/TB500, Cu-GHK, etc). High volume water based IM injections like L-carnitine carry higher risk of infection, so I try to avoid them. Risk of infection with subQ is essentially zero.Mug warmer is a great investment. Got it out of necessity for using TNE with no super solvents, but started warming everything up just to speed up the process as I use smaller gauge needles than most for drawing and injecting. Never struggled with pip on anything bad enough for it to be an issue for me personally, but that's definitely going to be another benefit of using a mug warmer for many.
I’m Sad opti doesn’t have it yetDHB has been my favorite compound to date .
