Glock45
Member
Says the dumb motherfucker who joins himself into the arguement
Last edited:
MESO-Rx
Anabolic Steroids
MESO-Rx Sponsor Pharmacom Labs officials and our Basicstero.com store
- Thread starter PHL Official
- Start date
BinGrey16
New Member
Anybody tried with WU?
So I got a crashed/cloudy vial of basicstero's Mast E. from the advice of a couple people in this thread i bought a candle warmer,one of these things:
Left it on a few hours and it cleared up perfectly but after it cooled down it went straight back to being cloudy. What the F am I doing wrong? Should I put it in the oven at a super high temperature? I'm afraid to inject this shit at this point. And yes, I use clean injection technique. I swap the vial with mckesson sterile alcohol wipes before drawing every time.
Last edited:
BigJP
Member
I am very curious about ordering using a personal CC. The thought of it kinda freaks me out but it's so convenient. Anybody that has done so please reply to this or just PM your experience doing so thus far....
So I got a crashed/cloudy vial of basicstero's Mast E. from the advice of a couple people in this thread i bought a candle warmer,one of these things:
Left it on a few hours and it cleared up perfectly but after it cooled down it went straight back to being cloudy. What the F am I doing wrong? Should I put it in the oven at a super high temperature? I'm afraid to inject this shit at this point. And yes, I use clean injection technique. I swap the vial with mckesson sterile alcohol wipes before drawing every time.
this is the same vial after only 5 minutes on the warmer. Clears right up.
but like i said it goes back to looking like the first picture after it cools down.
Pharmacom Helper
Subscriber
Hello guys, little remark about CC option: visa gets declined, mastercard works fine. So it means that ~90% payments by visa are blocked.
Looks like raw material not completely dissolved. You can try to heat it in microwave oven, if I remember well temperature for mast E = 68°C. Try to heat with next parameters: 600 watt 30 sek
p.s. guys if someone still have open questions with me - please remind me in PM
Looks like raw material not completely dissolved. You can try to heat it in microwave oven, if I remember well temperature for mast E = 68°C. Try to heat with next parameters: 600 watt 30 sek
p.s. guys if someone still have open questions with me - please remind me in PM
anfee
Well-known Member
I just wanted to be 100% that you are referring to the prepaid MasterCard has zero issues with purchasing from the online store, is that correct?
Anyone able to comment on if they have used this method yet?
I just put it in my microwave at full power (not sure how much wattage it is) for two 30 intervals right after one another. Went clear but now 5 minutes later it's cloudy as shit again.
Triton_
Subscriber
Prepaid cards do not work outside of the United States. Only the bank mastercards work..
anfee
Well-known Member
Thanks for the clarification.
Glock45
Member
It's fine. Heat it up til the crystals are gone, then shoot. You just might have to do that before every inject
BigJP
Member
@Pharmacom Helper does the site take discover
Glock45
Member
I was wondering the same thing
ScabbyJr
Well-known Member
IMO, he should send you a replacement bottle. Not this heat it up bullshit.
Glock45
Member
Pharma grade crashes too. It's nothing to do with the supplier. It happens
If your Watson looked like that and you took it back, it would be replaced.
Glock45
Member
This ain't Watson though is it? This is UGL big difference
agreed, but they do adverise pharma grade. doesn't mean the customer service should be different correct? I see your point though...
Glock45
Member
Fair enough
Similar threads
- Sticky
