PurplePandaLabs Raw source

[Ripped]

Anyone try the deca 500?

Wanting to know myself wonder about pip on it and the test 500.

 

[Ripped]

I'm new to running suspension I have some test really milky.
I shake it up and draw with a 23 gauge but in the barrel it looks like clear water is this normal or is my point to small to draw the hormone?

 

[CAswole]

Wanting to know myself wonder about pip on it and the test 500.

Idk dude I've used test e 500 b4 and that shit was literally crippling.

 

[Rockclimber]

Anything at 500mg/ml is going to cripple your ass. Better to dilute in half... 250mg/ml

 

[Ripped]

Idk dude I've used test e 500 b4 and that shit was literally crippling.

Yeah some can make it painless some can't .
It would be nice to do 2ml a week and get 1g in tho.

 

[Ripped]

Anything at 500mg/ml is going to cripple your ass. Better to dilute in half... 250mg/ml

Can't be any worse than some test ace I got damn I limped around for 2 weeks.

 

[CAswole]

Yeah some can make it painless some can't .
It would be nice to do 2ml a week and get 1g in tho.

Yeah in a perfect world buddy LOL. To tell you of my experience when I put 1 ml of test 500 in my right shoulder I literally could not reach my arm up far enough to work the air conditioning or radio in my car. Had to reach over with my left hand to work the controls LOL. Fuck that shit never again

 

[Ripped]

Yeah in a perfect world buddy LOL. To tell you of my experience when I put 1 ml of test 500 in my right shoulder I literally could not reach my arm up far enough to work the air conditioning or radio in my car. Had to reach over with my left hand to work the controls LOL. Fuck that shit never again

I put 1ml in glute and quad I had knots and had to drag my leg. may have to just get 300 mg.
NOTE: NOT PPL OILS.

 

[LordSamuilo]

I'm new to running suspension I have some test really milky.
I shake it up and draw with a 23 gauge but in the barrel it looks like clear water is this normal or is my point to small to draw the hormone?

No it should look just like it does in the vial when you shake it , but thats weird I always use 23g and it draws the powder in just fine ? But if you're having that happen id definitely use a larger gauge needle to draw with , because your just gonna end up making your vial more and more concentrated everytime you draw if its not pulling that crystal out..

 

[Ripped]

No it should look just like it does in the vial when you shake it , but thats weird I always use 23g and it draws the powder in just fine ? But if you're having that happen id definitely use a larger gauge needle to draw with , because your just gonna end up making your vial more and more concentrated everytime you draw if its not pulling that crystal out..

Thanks I may pick up some 18 g to draw it with.

 

[Poppindemthangz]

@purplepandalabs this may have been asked but what is domestic T/A on domestic shipments

 

[CAswole]

I put 1ml in glute and quad I had knots and had to drag my leg. may have to just get 300 mg.
NOTE: NOT PPL OILS.

Right lol. Important note that mine was also NOT PPL

 

[CAswole]

Thanks I may pick up some 18 g to draw it with.

Idk if 18g is quite necessary. I understand your intention my only concern there is after a few passes through the rubber stopper with an 18 gauge you may run the risk of chewing apart the Rubber and it possibly leaving particles in your Barrel. Just my thoughts

 

[Thegreek]

Idk if 18g is quite necessary. I understand your intention my only concern there is after a few passes through the rubber stopper with an 18 gauge you may run the risk of chewing apart the Rubber and it possibly leaving particles in your Barrel. Just my thoughts

What do you use to draw with. I've always used 18 and have at times wound up with bits but I would think anything smaller would just be super slow to draw and even with a smaller needle the constant passing through the rubber could still break off little pieces.

 

[CAswole]

What do you use to draw with. I've always used 18 and have at times wound up with bits but I would think anything smaller would just be super slow to draw and even with a smaller needle the constant passing through the rubber could still break off little pieces.

I've never needed to use anything larger than a 20. Works like a charm every time. Draws very quickly

 

[Leancuisine]

I'm sure it's been answered a few times already but...

Has anyone brewed the primo E? How's it going? Still on the fence about primo or just sticking with mast

 

[Thegreek]

I've never needed to use anything larger than a 20. Works like a charm every time. Draws very quickly

I still have a shit load of 18s but maybe I'll give 20s a go next time. Thanks man.

 

[Cyrix]

I've never needed to use anything larger than a 20. Works like a charm every time. Draws very quickly

I've always used 20g to draw too.

 

[Wood4days]

What do you use to draw with. I've always used 18 and have at times wound up with bits but I would think anything smaller would just be super slow to draw and even with a smaller needle the constant passing through the rubber could still break off little pieces.

I draw with 23g. Pull back slowly get some oil running then push out the air back into the vial until all you draw is oil. Works for me. I pin with 21g quicker for me. I tried pinning with 23g and it takes forever

 

[Cyrix]

I draw with 23g. Pull back slowly get some oil running then push out the air back into the vial until all you draw is oil. Works for me. I pin with 21g quicker for me. I tried pinning with 23g and it takes forever

I pin with a 25 and it doesn't take that long.