MESO-Rx

Anabolic Steroids

nerds everywhere man

PIZZABOY said:
I do., well the easy ones. Ive programmed and operated one in the shop by Accurouter, i use Rhino programing software. The thing is a dinasaur, yet a true work horse. I have to push 7 buttons to get it to cut, and then there is the vacumn. Rollers up, rollers down, its always fun cutting a new program for the first time, plunged the bit into the table once, or twice:(
Click to expand...
I was asking becuase i wanted someone to write some code for a gun part. I need to research the legality of it first. I got a complete lower assembly for a hk usc carbine, i already have another one complete so i was thinking i could use the other upper as a model to make another one. Not sure if it would be cost efective though, or legal
 
Logan44551 said:
I was asking becuase i wanted someone to write some code for a gun part. I need to research the legality of it first. I got a complete lower assembly for a hk usc carbine, i already have another one complete so i was thinking i could use the other upper as a model to make another one. Not sure if it would be cost efective though, or legal
Click to expand...
Well,if its like an AR, the serial numbers are on the lower, or is the HK different? Many ways to skin a cat. If you wanted to go into a small production run, then sure, it would be cost effective. Legality issues... Realy depends on the part. Many times having a certain part is fine, until you assemble it. Then troubles arise. If you drill 1 certain hole, just a hole mind you, in the wrong spot on an AR, you might get 10yrs Federal time.
 
PIZZABOY said:
Well,if its like an AR, the serial numbers are on the lower, or is the HK different? Many ways to skin a cat. If you wanted to go into a small production run, then sure, it would be cost effective. Legality issues... Realy depends on the part. Many times having a certain part is fine, until you assemble it. Then troubles arise. If you drill 1 certain hole, just a hole mind you, in the wrong spot on an AR, you might get 10yrs Federal time.
Click to expand...
What I am pulling out of your conversation at this point is that you guys should swap proton mail addresses and talk about this via email. No need to make the feds key off on Meso for conspiracy of illegal gun manufacturing or something :eek:o_O
 
Logan44551 said:
I was asking becuase i wanted someone to write some code for a gun part. I need to research the legality of it first. I got a complete lower assembly for a hk usc carbine, i already have another one complete so i was thinking i could use the other upper as a model to make another one. Not sure if it would be cost efective though, or legal
Click to expand...
From my former job I can tell you that would be illegal and the ATF would jam you up. Hard! I would keep it off this board. Just trying to help bro.
 
Logan44551 said:
I was asking becuase i wanted someone to write some code for a gun part. I need to research the legality of it first. I got a complete lower assembly for a hk usc carbine, i already have another one complete so i was thinking i could use the other upper as a model to make another one. Not sure if it would be cost efective though, or legal
Click to expand...
Also if you have a certified gunsmith near you have him do it. He will know exactly what can be legally done. Plus it will be his ass on the line if he fuks up. Like said before there are tons of legal modification kits. It becomes very dicey when you make just one simple mistake. Just be careful.
 
hurricane said:
From my former job I can tell you that would be illegal and the ATF would jam you up. Hard! I would keep it off this board. Just trying to help bro.
Click to expand...
If that's the case, i will abandon the project. I don't want to do anything to jepordize my right to keep and bear arms. Forget i mentioned it. Sorry for posting it on the board.
 
hurricane said:
How much snow you get fukr?? Just about 7" here. Now ice.
Click to expand...
Maybe 5" with ice on top. Nothing crazy, just cold and wet.

Wanna here something crazy? My father in law slipped on ice in the front yard the other morning and couldn't get up. He called my wife and we went out and picked him up and got him inside and all that. He goes to the hospital to het checked out and the man broke his neck. Not sure which c# it is. Has to wear a neck thing for a month now! Sucks!!!!
 
ickyrica said:
Maybe 5" with ice on top. Nothing crazy, just cold and wet.

Wanna here something crazy? My father in law slipped on ice in the front yard the other morning and couldn't get up. He called my wife and we went out and picked him up and got him inside and all that. He goes to the hospital to het checked out and the man broke his neck. Not sure which c# it is. Has to wear a neck thing for a month now! Sucks!!!!
Click to expand...
Fuk man! Lucky he wasn't paralyzed. Sounds like a tough old bastard.
 
ickyrica said:
Steven Hawkins died last night. It's always a bad thing when a mind like that leaves this earth. RIP
Click to expand...
Agreed,
Especially considering what seems to be out there now. I stress to my son that he's the next generation that we as adults depend on. How about you and your friends try not to fuck this place up anymore than it is. I try to keep my old school values in my kids and not this everyone gets a fucking trophy and smiley face sticker if there fucking feelings get hurt.

Sorry for the rant lol
 
You must log in or register to reply here.

Similar threads

D
Why not, I have room for another project or 6...
Replies
7
Views
143
dogfart
D
I
Clavicular doing a good job keeping BP tards off meso
2 3
Replies
40
Views
1K
MindlessWork
MindlessWork
OopsStinky
New member - long time lurker
Replies
0
Views
28
OopsStinky
OopsStinky
Tbaz192
Comeback log? We’ll see. Low ferritin gang.
Replies
3
Views
90
Tbaz192
Tbaz192
N
Intro
Replies
1
Views
26
Oldhand
Oldhand

Sponsors

Latest posts

Back
Top