[Source] Sasquatch Labs - Intro/Sale (US Domestic)

[Mem1guy]

Works every time in the microwave. No issue with the aluminum cap

 

[Easymod3]

Okay I’ll try that, I’ve just never experienced crashed gear before, thanks guys

 

[Easymod3]

So tried ten minutes in the oven at 175, vials got pretty toasty but the shit remains...I’ll try the microwave in a bit

 

[TideGear]

So tried ten minutes in the oven at 175, vials got pretty toasty but the shit remains...I’ll try the microwave in a bit

Not sure but maybe you have to vent with a needle. Can someone elaborate on this?

 

[Mem1guy]

Not sure but maybe you have to vent with a needle. Can someone elaborate on this?

Yes. Vent with needle

 

[Slammich]

Yes. Vent with needle

Sometimes i vent with a needle. Sometimes i vent with my homies at the bar. But i don't ever vent to my woman. She will just turn it around and make it my fault and all about her. Be careful how you vent is what I'm saying here.

 

[crau85]

Don’t put that in the microwave.. you don’t want to over heat the hormone. The microwave is not a controlled temperature source. Try baking for 20 minutes at 200*

So tried ten minutes in the oven at 175, vials got pretty toasty but the shit remains...I’ll try the microwave in a bit

 

[Mem1guy]

30 seconds at a time and most will go back in 1 minute total. The bottle never goes over 200 degrees. Mast p melting point is around 260 degrees.

 

[Brucie]

The microwave sounds like a really bad idea to me, alum top or not. But what do I know.

 

[Mimmik]

Frying pan on the stove top.

1) Put 1-1.5” of water in the pan (enough to go 3/4 way up the vial)

2) Heat water to just under a boil, turn off burner

3) Place vial upright in water

4) Lift and swirl vial by hand every 15-20 seconds until hormone is dissolved

 

[Iron Frenchie]

Those test results were nice to see. Looking good.

 

[XKawN]

So tried ten minutes in the oven at 175, vials got pretty toasty but the shit remains...I’ll try the microwave in a bit

200f in the oven for about 30 minutes then wait for it to cool enough to handle and then shake well. No need to take cap off or vent. I don't put my products anywhere near water so water bath is out for me.

 

[Gobuckeyes0122]

Yes and no

I have absolutely no idea what the typical margin of error for an underground lab is.

Superdrol ---> +17%
Anavar ---> +11%
Anadrol ---> -18%
Test E ---> +14%
Tren E ---> 0.50% (Good)
Mast E ---> 7.5%

All except the Tren E. are well outside the advertised dose. That said all are within +/-20%. Sadly some compounding pharmacies fall well outside this range:

Accuracy of Testosterone Concentrations in Compounded Testosterone Products

How the fuck where those labs so far off and it be aloud? I read that whole article and I don’t know how it’s legal for a company to do that?

 

[Bigboy727]

200f in the oven for about 30 minutes then wait for it to cool enough to handle and then shake well. No need to take cap off or vent. I don't put my products anywhere near water so water bath is out for me.

I run the bottom of the vials under the tap before injections. Been doing it that way for years. Just don’t be an idiot and run it over the top.

 

[rpbb]

How the fuck where those labs so far off and it be aloud? I read that whole article and I don’t know how it’s legal for a company to do that?

Legal? Go do some reading and come back when you have a clue

 

[Bigboy727]

Legal? Go do some reading and come back when you have a clue

How dare these illegal labs not follow legal guidelines.

 

[XKawN]

I run the bottom of the vials under the tap before injections. Been doing it that way for years. Just don’t be an idiot and run it over the top.

I just find there's better ways to do it, imo. In a steam bath you have steam rising and has a possibilty of introducing it's self into your product. May get away with doing that many times. Maybe even forever, but i just don't take the chance. But we do what works for us.

 

[WhiteHotWombat]

So tried ten minutes in the oven at 175, vials got pretty toasty but the shit remains...I’ll try the microwave in a bit

Use a hair dryer - easy to control and effective

 

[Sasquatch Labs]

I recommend using a heating pad. If you were to already have pierced the stopper, you want to use dry heat and have limited air flow.

Jay

 

[Sasquatch Labs]

How dare these illegal labs not follow legal guidelines.

I believe he was referencing this link: Accuracy of Testosterone Concentrations in Compounded Testosterone Products

These products were made legally and a few fell outside 20%.

Jay