Dirts Brew log

[jJjburton]

It's actually a little more work than I though.. I don't have a dedicated spot for a lab so I spend a lot of time bleaching counter tops then leaning them with dush soap then rinsing with distilled water and wiping down with alcohol then I spread out painters paper. Then kinda the same process for the equipment I use.. making the dope is quick and easy. Then cleaning everything and putting up..

Yes that doesnt look amazingly sterile, especially if you use the same hose over and over, the oil builds up inside the tube?

 

[Dirthand]

Yes that doesnt look amazingly sterile, especially if you use the same hose over and over, the oil builds up inside the tube?

I'm not sure I understand what you are talking about?

 

[Dirthand]

Weeky weekend brew:
Test E 300
2%ba
18%bb
Mct
Deca 300
2%ba
20%bb
Mct
Any opinions?

 

[eery]

Weeky weekend brew:
Test E 300
2%ba
18%bb
Mct
Deca 300
2%ba
20%bb
Mct
Any opinions?

From what ive heard, you can probably push the deca up to 400-450mg/ml with 20%bb in mct

 

[Dirthand]

From what ive heard, you can probably push the deca up to 400-450mg/ml with 20%bb in mct

Any bit with deca at 400?

 

[eery]

Any bit with deca at 400?

Not from what ive heard from the guys i talked to.

 

[LGOP528]

Curious about this also. I put them both in steroidplotter and it looks like test D at the same dose and frequency is a higher concentration. Cyp is the lower one. Both 250mg every 3.5 days.

I ran into this same problem when I was trying to work out switching from a blast to a cruise. I think there is something wrong with the new site. Using the old site, it shows correct. The new site shows it as a higher concentration with a lower dose of Test D. These are switching from 500/week test c to 350/week test d at the 11 week mark.

 

[Akc83]

@dirthand you still waiting on those filters from ks-tek?

 

[Dirthand]

@dirthand you still waiting on those filters from ks-tek?

Yes, the tracking number they gave me does not register but i have been in communication with them and have assured me they are on the way.

 

[Akc83]

Yes, the tracking number they gave me does not register but i have been in communication with them and have assured me they are on the way.

I just ordered some Tuesday. I didn’t have good luck with my millipore pvdf. Could be the raws also they may have had some moisture in them. Test E is hazy looking. Going to wait for the new filters and reheat and refilter to see if that works.

 

[Dirthand]

I just ordered some Tuesday. I didn’t have good luck with my millipore pvdf. Could be the raws also they may have had some moisture in them. Test E is hazy looking. Going to wait for the new filters and reheat and refilter to see if that works.

One thing I have noticed is when I filter from bottle top into media bottle the gear looks a little cloudy.. however when I transfer it to sterile smaller vials the cloudiness goes away.. I think it's just the glass on the media Bottles. I noticed this when I made tren and mast.. lastnight I made 2 batches of Test E and the same thing.

 

[Ghoul]

One thing I have noticed is when I filter from bottle top into media bottle the gear looks a little cloudy.. however when I transfer it to sterile smaller vials the cloudiness goes away.. I think it's just the glass on the media Bottles. I noticed this when I made tren and mast.. lastnight I made 2 batches of Test E and the same thing. View attachment 291281

I don't think that's the glass. There's just more of it, so the cloudiness is apparent.

 

[Dirthand]

I don't think that's the glass. There's just more of it, so the cloudiness is apparent.

Well since you are just looking at a picture.. and I have thouroly investigated the matter in person.. I'll take your word for it...

 

[Akc83]

One thing I have noticed is when I filter from bottle top into media bottle the gear looks a little cloudy.. however when I transfer it to sterile smaller vials the cloudiness goes away.. I think it's just the glass on the media Bottles. I noticed this when I made tren and mast.. lastnight I made 2 batches of Test E and the same thing. View attachment 291281

Mine is still cloudy after I transferred to vial.

 

[Ghoul]

Well since you are just looking at a picture.. and I have thouroly investigated the matter in person.. I'll take your word for it...

Dude, I'm just pointing out that when a container is wider and you're looking thorough more of a liquid, cloudiness is more easily seen. Pull clearly cloudy liquid from a vial into a syringe and often it looks crystal clear.

 

[Dirthand]

Dude, I'm just pointing out that when a container is wider and you're looking thorough more of a liquid, cloudiness is more easily seen. Pull clearly cloudy liquid from a vial into a syringe and often it looks crystal clear.

And I'm just pointing out to you that I have definantly considered that, investigated and that's not the case here.

 

[Dirthand]

Dude, I'm just pointing out that when a container is wider and you're looking thorough more of a liquid, cloudiness is more easily seen. Pull clearly cloudy liquid from a vial into a syringe and often it looks crystal clear.

And honestly if that was the case I would just state "this gear I made is cloudy.. imma bang it and see how it goes"

 

[Dirthand]

Mine is still cloudy after I transferred to vial.

Hmm what a as the BB %

 

[Akc83]

Hmm what a as the BB %

15% BB
1.5%BA

 

[Dirthand]

15% BB
1.5%BA

Would definantly be a question for some of these more experienced guys. I wouldn't think q5% would be to high for a pvdf. What vacuum pressure did you filter it at? I try and stay around 18psi.