Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I dose with an insulin syringe with the needle cut off
Anyway do you think there would be health benefits to switching besides lower impact on hematocrit?
Thanks for posting. Brings up a good point. These would dissolve too fast. Need to add some higher MW PEG to slow the dissolution rate so the Flux through the oral mucosa using the buccal route matches the dissolution rate. See that nice recipe I posted up earlier in thread.Testosterone 1 mg Troches
www.uspharmacist.com
Thanks for posting. Brings up a good point. These would dissolve too fast. Need to add some higher MW PEG to slow the dissolution rate so the Flux through the oral mucosa using the buccal route matches the dissolution rate. See that nice recipe I posted up earlier in thread.
You don't want a lot of liquid just sitting around. That's why the sublingual route is inferior to buccal. Dilution with saliva which lowers the driving force and promotes swallowing.
Just don't choke. Safety first.I remember when i was taking a certain medication sublingually i would put it in my mouth while still in bed then go back to sleep for another half hour before getting up. This solved the problem of saliva flooding the mouth.


I made some buccal troche lozenges, out of curiosity, after seeing this thread.
Adrol 20mg.
Pros:
- Easier/less mess to make vs capping enteric coated capsules.
- Tastes fking good, i used 2% menthol,. Will add coffee extract next time.
- Takes about 20-30 minutes to dissolve when placed on the gumline.
- You actually feel it kicking in.
Neat! How much do you think actually gets absorbed versus swallowed? Got any indirect methods of estimating that, like reduction in GI impact?
Seems like the enteric capsules are a more surefire way to skip over the stomach, at the cost of the digestive delay. With a troche, you’re likely swallowing *some* of the API, right?That's the part, I don't really know the % improvement in the absorption rate lol. I place my orals in enteric coated capsules so it bypasses the stomach either way which reduces any impact it has on my GI.
Seems like the enteric capsules are a more surefire way to skip over the stomach, at the cost of the digestive delay. With a troche, you’re likely swallowing *some* of the API, right?
I made some buccal troche lozenges, out of curiosity, after seeing this thread.
Adrol 20mg.
Pros:
- Easier/less mess to make vs capping enteric coated capsules.
- Tastes fking good, i used 2% menthol,. Will add coffee extract next time.
- Takes about 20-30 minutes to dissolve when placed on the gumline.
- You actually feel it kicking in.
Cons:
- Not sure about bioavailability vs enteric coated capsules.
- Made of PG and doesn't break off evenly even if it's scored, which makes dosing accurately difficult. I can see why UGL won't touch this.
- Also breaks on impact.
Each troche is 1mg and scored, can be broken into 4 pieces.
View attachment 336426
View attachment 336425
I made some buccal troche lozenges, out of curiosity, after seeing this thread.
Adrol 20mg.
Did you use the PEG MW combo in the recipe above or what?Pros:
- Easier/less mess to make vs capping enteric coated capsules.
- Tastes fking good, i used 2% menthol,. Will add coffee extract next time.
- Takes about 20-30 minutes to dissolve when placed on the gumline.
- You actually feel it kicking in.
Cons:
- Not sure about bioavailability vs enteric coated capsules.
- Made of PG and doesn't break off evenly even if it's scored, which makes dosing accurately difficult. I can see why UGL won't touch this.
- Also breaks on impact.
Each troche is 1mg and scored, can be broken into 4 pieces.
Thanks so much for sharing your success.
impressive, how do you make these?
Tremendous! Well done.
Did you use the PEG MW combo in the recipe above or what?
I'd think the biggest issue UGL would have would be them melting in transit. To avoid you'd have to use a higher MW PEG that wouldn't dissolve in the mouth very well. You can tailor the dissolution rate with the PEG MWD used.
Each troche contains 20 mg?
Thanks so much for sharing your success.
Very impressive variance with the quarters. Hat tip.Troche base - Techna 10
Weighing scale.
Beaker, raws, small spoon, heat, stir.
Cool in mold in the fridge.
Add flavoring if you want, i used concentrated menthol, you can get lemon/ coffee, whatever flavoring.
No beaker? just use a cup.
Small spoon to break up any chunks.
It's too thick so a magnetic stirrer won't work.
It's more hands off than capping raws or making tabs.
To be more specific, each square has 80g of drol, which weighs 1.20g, which is scored into 4, which can be broken easily into 4 pieces, which contains 20mg drol each.
Melting point 40-50 C.
To be more specific, each square has 80mg of drol, which weighs 1.20g, which is scored into 4, which can be broken easily into 4 pieces, which contains 20mg drol each.
Have you shared this data anywhere before? I don't have a vulva but I have test cream and an anus. However mixing the two I'm not so sure about.It is in realm of feasible (see turinabol cocktail saga and E Germans before that). Shared that in the steroid forum.
BTW I have a great data set showing test cream applied to anus or vulva has elimination half life under 1 hr. Similar to Natesto. But you really have to know what you are doing with WADA testing. Complicated is short answer.
Excellent work!Troche base - Techna 10
Weighing scale.
Beaker, raws, small spoon, heat, stir.
Cool in mold in the fridge.
Add flavoring if you want, i used concentrated menthol, you can get lemon/coffee, whatever flavoring.
No beaker? just use a cup.
Small spoon to break up any chunks.
It's too thick so a magnetic stirrer won't work.
It's more hands off than capping raws or making tabs.
To be more specific, each square has 80g of drol, which weighs 1.20g, which is scored into 4, which can be broken easily into 4 pieces, which contains 20mg drol each.
Melting point 40-50 C.
So if I'm understanding correctly each mold contains 80mg anadrol and around 1g techna 10 plus sweetener/flavoring? I really want to try this out if I don't need a license to order the techna 10 and troche molds. I have raws for anadrol and superdrol that I could try. ThanksTroche base - Techna 10
Weighing scale.
Beaker, raws, small spoon, heat, stir.
Cool in mold in the fridge.
Add flavoring if you want, i used concentrated menthol, you can get lemon/coffee, whatever flavoring.
No beaker? just use a cup.
Small spoon to break up any chunks.
It's too thick so a magnetic stirrer won't work.
It's more hands off than capping raws or making tabs.
To be more specific, each square has 80g of drol, which weighs 1.20g, which is scored into 4, which can be broken easily into 4 pieces, which contains 20mg drol each.
Melting point 40-50 C.
