Its brew time!!

[colossus25]

Finally was able to brew some gear up. Now this isn't a how to guide just a quick glimpse at what i do and the steps i take when i brew. I AM NOT A SOURCE!!! Don't PM me asking for gear, you will be kindly told to kill yourself. All that said lets get going.

I received my brew ware in the mail today and here is a pic:

 

[colossus25]

I always rinse my hands thoroughly with alcohol. Rinse and repeat. And i wear gloves and change gloves a few times through out the process

 

[colossus25]

Next i plug my desired mg/ml and how much ill be making into http://www.everydayfitness.net/steroid-powder-calculator.html. Once i have that i scale out how ever much i need of whatever compound i am using, in this case tren.

 

[colossus25]

Next i add the appropriate amount of BA and BB to the raw powder in a graduated beaker.

 

[colossus25]

Next i preheat a pan with water in it to the tren ace raw melting point, in this case just over 200 degrees. I stir with a glass rod until all the powder melts.

 

[colossus25]

Next i add the carrier oil to the solution once all the powder has melted. I used MCT oil this time around.

 

[colossus25]

Next i prep my vial with an 18g and a filter. Then after i draw up everything from the beaker into a syringe.

 

[colossus25]

Then i place the syringe in a caulking gun and attach it to the vial. I almost forgot to mention to leave an 18g in there to vent out the pressure of the vials. Little by little with out being to aggressive i get the solution into the vial.

 

[colossus25]

Once done thats it you have gear ready to pin. Pull out your syringe and clean up your work area.

 

[MisterSuperGod]

Am very tempted to try brewing, at some point.

This thread you put together is pretty straight forward, job well done!

 

[ickyrica]

Looks good. Next time use different rubbing alcohol though. Use the 70% kind. The 90% kind evaporates fast and may leave bad shit behind. The 70% takes long enough to evaporate that it kills everything. I'm sure someone could be more eloquent with an answer on this but I'm certain that you want 70%.

 

[TRT]

Good job buddy. I can see we have a lot of the same stuff. Where are you getting the box of 60ml syringes though?

 

[colossus25]

Am very tempted to try brewing, at some point.

This thread you put together is pretty straight forward, job well done!

It is not very difficult at all but do tons of research before attempting. Learn about the different solvents used to help suspend the aas in oil. Then look up the initial cost of everything, its not outrageously expensive or anything but it does take a couple hundred bucks to get the right stuff. Also i didn't include how i sterilize my work area or glassware, Research that too. It sounds like a lot but it really isn't.

 

[colossus25]

Looks good. Next time use different rubbing alcohol though. Use the 70% kind. The 90% kind evaporates fast and may leave bad shit behind. The 70% takes long enough to evaporate that it kills everything. I'm sure someone could be more eloquent with an answer on this but I'm certain that you want 70%.

I never really thought of that, thanks brother. The reason i have 91% is because i also use it to clean up my work station but for the same reason im thinking 70% might be better.

 

[colossus25]

Good job buddy. I can see we have a lot of the same stuff. Where are you getting the box of 60ml syringes though?

PM'd ya

 

[colossus25]

Shortly ill post up a little more detail on everything. I was half asleep last night and got lazy haha

 

[colossus25]

@Thegreek

 

[colossus25]

@TRT i used a new recipe for the prop and its even more pain less than my last. Makes 50ml of finished product:

5 grams test prop raw.
5ml BB
1ml BA
44ml of MCT

 

[TRT]

@TRT i used a new recipe for the prop and its even more pain less than my last. Makes 50ml of finished product:

5 grams test prop raw.
5ml BB
1ml BA
44ml of MCT

Fucking nice. You ever notice that some batches can be different then others? Sometimes ill end up having to add more BB to keep it suspended. I don't use prop myself but my notes say I use an average of 7ml of BB in 50ml. Thought it was way more then that.

How long has it been suspended for now?

 

[TRT]

@colossus25

Since we're talking about BB and suspending. What's the longest you've seen a solution stay suspended before crashing? I know atmosphere temp and house temp play a roll in this but I'm pretty sure we're in the same area. [emoji6]