Date_Mike
Subscriber
I plan to make a solution with DMSO for the Var. according to cayman chemicals , it’s soluble up to 20mg/ml
MESO-Rx
Anabolic Steroids
Qingdao Sigma Chemical Co., Ltd (International, US, EU, Canada and Australia domestic
- Thread starter Qingdao Sigma Chemicals
- Start date
gettinginshape
New Member
Aromasin was soluble at 10mg/mL into MCT oil without much issue for me on a hotplate. Tastes pretty neutral and easy to dose with a 3mL slip tip syringe.
Some sources also indicate solubility in ethanol up to 15mg/mL or DMSO at 54mg/mL.
Maybe he's just looking for a date. Wants to make sure you're in shape and ready for it. lol
PrimoBowling
New Member
Rimobolan never caused me any post inject pain.
Some guys are just lucky, some aren't. I brew mine at 125mg and I'm fine, my cousin has to mix it with his test and need to go .5ml every shot or else it's swelling time. Hence, he switched to masteron lol.
Rido
Subscriber
Hey buddy, I think xkawn has talked about some reports of anavar being 19mg/ml in solution before.
I remember seeing an old post on it from the past when. I was researching capping for liquid
PrimoBowling
New Member
That sounds familiar.
Rido
Subscriber
here we go
everyone else has already blocked him. There was like a page and a half long discussion about it within the past month or so.
about half the reviews here on the primo 200 say "zero pip" and half of them say "significant pip". Even QSC says it's about 50/50 whether someone gets PIP from it or not. Wish they still had primo 100 but that's what home brewing is for.
Only in some kind of super solvent. It's basically insoluble in oils or water. Water solubility is <0.5mg/ml. Some sources put it at 0.014 mg/mL in water.
I think I remember seeing anavar / oxandrolone being soluble in oil up to about 2-3mg/mL. I can't find where I found that anymore but I do see this study which achieved 2mg/mL in sesame oil, so I think that's about the right range. All other studies I can find now used concentration of 0.025 to 1 mg/mL, this is the only one I could find >1mg/mL.
Anything you find higher than this either uses guaiacol or DMSO ... or it was a "home-brew" recipe for a suspension, not a solution, which (as you know but other people might now) would only be appropriate for oral, not injection. e.g. using Ora-Plus. You'd probably still want to shake the bottle every day just to be sure the oral suspension is well-mixed.
Personally I stay away from DMSO because I'm completely unable to assess its risks but other people are more comfortable with it than I am. It is reasonable soluble in DMSO, reportedly "up to" 20mg/mL but I'd take that with a grain of salt.
I also stay away from guaiacol but again, other people are more comfortable with it than I am (the injectable superdrol uses this).
@Qingdao Sigma Chemicals -- anything besides superdrol that your engineer uses guaiacol with?
Last edited:
Date_Mike
Subscriber
He probably did that just to make sure he didn’t saturate. I was considering doing the same. Will do that for sure. Thanks bro
Date_Mike
Subscriber
Ahh sorry @connoristiny ladies only. Tit pics or gtfo
I really don't think oil alone can hold 19mg/mL, but please try it and report back.
Date_Mike
Subscriber
Cayman chems had the solubility of dmso at 20mg/ml and xkawn is a very knowledgeable well know member here. Plus dmso is an organic super solvent, it holds almost every substance at a higher concentration than PG/PEG400/H2O.
I’m confident It’ll dissolve at 19mg/ml but I will report back.
Dmso has a strong smell if used orally. Like rotten eggs or garlic. Use peg with dmso or use ethanol
HellNikki
New Member
Date_Mike
Subscriber
Date_Mike
Subscriber
I was looking into ethanol but solubility of oxandrolone is only 2mg/ml.
DMSO shouldn’t cause bad breath or other sides used at low amounts. If I notice anything I’ll stop and just make a suspension with peg or pg
Lutzlutzington
New Member
Similar threads
